Init m5Stickc Plus

Author: 1technophile

docs/prerequisites/M5.md

@@ -1,8 +1,8 @@
 # M5 Boards
 M5 boards, manufactured by [M5Stack](https://m5stack.com/) are inexpensive, well featured boards based on ESP32.
 
-## M5StickC and M5Stack
-M5StickC and M5Stack are supported by OpenMQTTGateway and provide the following features:
+## M5StickC, M5StickC Plus and M5Stack
+M5StickC, M5StickC Plus and M5Stack are supported by OpenMQTTGateway and provide the following features:
 
 ### 3 low power modes 
 #### Always ON display

docs/prerequisites/board.md

@@ -19,6 +19,7 @@ The boards below doesn't need hardware modification (or a lite one).
 |[M5Stack Basic](M5)|![](../img/OpenMQTTgateway_M5_Stack_Board_Display_Text.png)|-|-|X|-|X|X|X|
 |M5Stick|-|-|send|X|-|X|-|X|
 |[M5Stick C](M5)|![](../img/OpenMQTTgateway_M5_StickC_Board_Display_Text.png)|-|send|X|-|X|X|X|
+|[M5Stick C Plus](M5)|-|-|send|X|-|X|X|X|
 |[M5Atom](M5)||-|send|X|-|X|X|X|
 |TTGO LORA32|![](../img/OpenMQTTGateway_TTGO32_LORA_Send.jpg)|-|-|-|X|-|-|-|
 |Sonoff RFR3|![](../img/OpenMQTTGateway_boards_sonoff_rfr3.png)|[receiving](https://1technophile.blogspot.com/2019/08/new-sonoff-rfr3-as-433tomqtt-gateway.html)|-|-|-|X|-|-|

docs/use/boards.md

@@ -7,7 +7,7 @@
 So as to erase the flash memory on ESP boards you may do a long press to TRIGGER_GPIO button or connect the pin TRIGGER_GPIO to the ground during several seconds.
 
 On M5Stack boards you may do a long press to these buttons:
-* Button B on M5StickC (GPIO 37)
+* Button B on M5StickC and M5StickC Plus (GPIO 37)
 * Button C on M5Stack (GPIO 37)
 * Button lateral on M5stick (GPIO 35)
 
@@ -31,15 +31,15 @@ When coming back from mode 2 to mode 0 you may publish the command with a retain
 If you change the default low power mode in config_BT.h to 2 and your credential are not set or not correct, the ESP32 will not connect to the broker and the only way to change the low power mode will be a new erase/upload.
 :::
 
-## M5Stick C or M5Stack
+## M5StickC, M5StickC Plus or M5Stack
 
 ### Behaviour
 
 If the connexion of the board to WIFI and MQTT is successfull you will see the logo with text like below:
 
 ![boards](../img/OpenMQTTgateway_M5_Stack_Board_Display_Text.png)
 
-The same behaviour apply to M5 Stick C
+The same behaviour apply to M5StickC and M5StickC Plus
 
 ![boards](../img/OpenMQTTgateway_M5_StickC_Board_Display_Text.png)
 
@@ -66,8 +66,8 @@ OpenMQTTGateway support a low power mode for ESP32, this mode can be set by MQTT
 
 `mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoBT/config" -m '{"low_power_mode":1}'`
 
-* Low Power mode, screen OFF, LED ON when processing on M5StickC
+* Low Power mode, screen OFF, LED ON when processing on M5StickC or M5stickC Plus
 
 `mosquitto_pub -t "home/OpenMQTTGateway/commands/MQTTtoBT/config" -m '{"low_power_mode":2}'`
 
-The low power mode can be changed also with a push to button B when the board is processing (top button on M5stickC and middle button of M5stack).
+The low power mode can be changed also with a push to button B when the board is processing (top button on M5stickC, M5stickC Plus and middle button of M5stack).

main/User_config.h

@@ -229,6 +229,7 @@ uint8_t wifiProtocol = 0; // default mode, automatic selection
 //#define ZmqttDiscovery "HADiscovery"//ESP8266, Arduino, ESP32, Sonoff RF Bridge
 //#define ZactuatorFASTLED "FASTLED" //ESP8266, Arduino, ESP32, Sonoff RF Bridge
 //#define ZboardM5STICKC "M5StickC"
+//#define ZboardM5STICKCP "M5StickCP"
 //#define ZboardM5STACK  "ZboardM5STACK"
 //#define ZradioCC1101   "CC1101"   //ESP8266, ESP32
 //#define ZactuatorPWM   "PWM"      //ESP8266, ESP32

main/ZboardM5.ino

@@ -28,10 +28,13 @@
 */
 #include "User_config.h"
 
-#if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
 #  ifdef ZboardM5STICKC
 #    include <M5StickC.h>
 #  endif
+#  ifdef ZboardM5STICKCP
+#    include <M5StickCPlus.h>
+#  endif
 #  ifdef ZboardM5STACK
 #    include <M5Stack.h>
 #  endif
@@ -43,7 +46,7 @@ void setBrightness(int brightness) {
 #  ifdef ZboardM5STACK
   M5.Lcd.setBrightness(brightness * 2);
 #  endif
-#  ifdef ZboardM5STICKC
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP)
   (!brightness) ? M5.Axp.ScreenBreath(0) : M5.Axp.ScreenBreath(7 + (int)brightness * 0.08);
 #  endif
 }
@@ -84,7 +87,7 @@ void sleepScreen() {
 #  ifdef ZboardM5STACK
   M5.begin(false, false, false); // M5.lcd.sleep() provokes a reset of the ESP
 #  endif
-#  ifdef ZboardM5STICKC
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP)
   M5.Axp.ScreenBreath(0);
   M5.Axp.SetLDO2(false);
 #  endif

main/ZgatewayBT.ino

@@ -631,7 +631,7 @@ void lowPowerESP32() // low power mode
 }
 
 void deepSleep(uint64_t time_in_us) {
-#    if defined(ZboardM5STACK) || defined(ZboardM5STICKC)
+#    if defined(ZboardM5STACK) || defined(ZboardM5STICKC) || defined(ZboardM5STICKCP)
   sleepScreen();
   esp_sleep_enable_ext0_wakeup((gpio_num_t)SLEEP_BUTTON, LOW);
 #    endif
@@ -649,12 +649,12 @@ void deepSleep(uint64_t time_in_us) {
 
 void changelow_power_mode(int newLowPowerMode) {
   Log.notice(F("Changing LOW POWER mode to: %d" CR), newLowPowerMode);
-#    if defined(ZboardM5STACK) || defined(ZboardM5STICKC)
+#    if defined(ZboardM5STACK) || defined(ZboardM5STICKC)  || defined(ZboardM5STICKCP)
   if (low_power_mode == 2) {
 #      ifdef ZboardM5STACK
     M5.Lcd.wakeup();
 #      endif
-#      ifdef ZboardM5STICKC
+#      if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP)
     M5.Axp.SetLDO2(true);
     M5.Lcd.begin();
 #      endif

main/config_M5.h

@@ -29,6 +29,9 @@
 #ifdef ZboardM5STICKC
 #  include <M5StickC.h>
 #endif
+#ifdef ZboardM5STICKCP
+#  include <M5StickCPlus.h>
+#endif
 #ifdef ZboardM5STACK
 #  include <M5Stack.h>
 #endif

main/main.ino

@@ -132,7 +132,7 @@ JsonArray& modules = modulesBuffer.createArray();
 #ifdef ZactuatorPWM
 #  include "config_PWM.h"
 #endif
-#if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
 #  include "config_M5.h"
 #endif
 #if defined(ZgatewayRS232)
@@ -466,7 +466,7 @@ void connectMQTT() {
   strcat(topic, will_Topic);
   client.setBufferSize(mqtt_max_packet_size);
   if (client.connect(gateway_name, mqtt_user, mqtt_pass, topic, will_QoS, will_Retain, will_Message)) {
-#if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
     if (low_power_mode < 2)
       M5Display("MQTT connected", "", "");
 #endif
@@ -547,7 +547,7 @@ void setup() {
   preferences.begin(Gateway_Short_Name, false);
   low_power_mode = preferences.getUInt("low_power_mode", DEFAULT_LOW_POWER_MODE);
   preferences.end();
-#    if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#    if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
   setupM5();
 #    endif
 #  endif
@@ -807,7 +807,7 @@ void setOTA() {
 #  if defined(ZgatewayBT) && defined(ESP32)
     stopProcessing();
 #  endif
-#  if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
     M5Display("OTA in progress", "", "");
 #  endif
   });
@@ -816,7 +816,7 @@ void setOTA() {
 #  if defined(ZgatewayBT) && defined(ESP32)
     startProcessing();
 #  endif
-#  if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
     M5Display("OTA done", "", "");
 #  endif
   });
@@ -1046,7 +1046,7 @@ void setup_wifimanager(bool reset_settings) {
   {
 #  ifdef ESP32
     if (low_power_mode < 2) {
-#    if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#    if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
       M5Display("Connect your phone to WIFI AP:", WifiManager_ssid, WifiManager_password);
 #    endif
     } else { // in case of low power mode we put the ESP to sleep again if we didn't get connected (typical in case the wifi is down)
@@ -1073,7 +1073,7 @@ void setup_wifimanager(bool reset_settings) {
     }
   }
 
-#  if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
   if (low_power_mode < 2)
     M5Display("Wifi connected", "", "");
 #  endif
@@ -1346,7 +1346,7 @@ void loop() {
 #endif
   }
 // Function that doesn't need an active connection
-#if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
   loopM5();
 #endif
 }
@@ -1392,7 +1392,7 @@ void stateMeasures() {
   SYSdata["m5-is-charging"] = (bool)M5.Power.isCharging();
   SYSdata["m5-is-chargefull"] = (bool)M5.Power.isChargeFull();
 #  endif
-#  ifdef ZboardM5STICKC
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP)
   M5.Axp.EnableCoulombcounter();
   SYSdata["m5-bat-voltage"] = (float)M5.Axp.GetBatVoltage();
   SYSdata["m5-bat-current"] = (float)M5.Axp.GetBatCurrent();
@@ -1514,7 +1514,7 @@ void receivingMQTT(char* topicOri, char* datacallback) {
 #  ifdef ZactuatorPWM
     MQTTtoPWM(topicOri, jsondata);
 #  endif
-#  if defined(ZboardM5STICKC) || defined(ZboardM5STACK)
+#  if defined(ZboardM5STICKC) || defined(ZboardM5STICKCP) || defined(ZboardM5STACK)
     MQTTtoM5(topicOri, jsondata);
 #  endif
 #  ifdef ZactuatorONOFF // outside the jsonpublishing macro due to the fact that we need to use simplepublishing with HA discovery

platformio.ini

@@ -44,6 +44,7 @@ extra_configs =
 ;default_envs = esp32-m5stick-ble
 ;default_envs = esp32-m5stack-ble
 ;default_envs = esp32-m5stick-c-ble
+;default_envs = esp32-m5stick-cp-ble
 ;default_envs = esp32-m5atom
 ;default_envs = ttgo-lora32-v1
 ;default_envs = nodemcuv2-rf
@@ -104,6 +105,7 @@ fastled = FastLED@3.3.2
 onewire = OneWire
 dallastemperature = DallasTemperature
 m5stickc = M5StickC@0.2.0
+m5stickcp = https://github.com/m5stack/M5StickC-Plus.git
 m5stack = M5Stack@0.3.0
 smartrc-cc1101-driver-lib = SmartRC-CC1101-Driver-Lib@2.3.5
 stl = https://github.com/mike-matera/ArduinoSTL.git#7411816
@@ -405,6 +407,32 @@ build_flags =
   '-DGateway_Name="OpenMQTTGateway_ESP32_M5STICK_C_BLE_IR"'
 board_upload.speed = 1500000
 
+[env:esp32-m5stick-cp-ble]
+platform = ${com.esp32_platform}
+board = pico32
+board_build.partitions = min_spiffs.csv
+lib_deps =
+  ${com-esp.lib_deps}
+  ${libraries.ble}
+  ${libraries.m5stickcp}
+  ${libraries.irremoteesp}
+build_flags =
+  ${com-esp.build_flags}
+  '-DZgatewayBT="BT"'
+  '-DZgatewayIR="IR"'
+  '-DZsensorGPIOInput="GPIOInput"'
+  '-DZboardM5STICKCP="M5StickCP"'
+  '-DACTUATOR_ONOFF_GPIO=10'
+  '-DINPUT_GPIO=37'
+  '-DLED_RECEIVE=10'
+  '-DLED_RECEIVE_ON=0'
+  '-DSLEEP_BUTTON=39'
+  '-DTRIGGER_GPIO=39'
+  '-DIR_EMITTER_INVERTED=true'
+  '-DIR_EMITTER_GPIO=9'
+  '-DGateway_Name="OpenMQTTGateway_ESP32_M5STICK_CP_BLE_IR"'
+board_upload.speed = 1500000
+
 [env:esp32-m5atom]
 platform = ${com.esp32_platform}
 board = pico32