4.7:StellarF4

Author: Hwurzburg

common/source/docs/common-autopilots.rst

@@ -176,6 +176,7 @@ Closed Hardware
     SpeedyBee F4 V3/V4 <common-speedybeef4-v3>
     SpeedyBee F405 Mini <common-speedybeef405-mini>
     SpeedyBeeF405WING/WING Mini <common-speedybeef405wing>
+    StellarF4 <common-stellarf4>
     TBS Lucid H7 <common-tbs-lucidh7>
     ThePeach FCC-K1 <common-thepeach-k1>
     ThePeach FCC-R1 <common-thepeach-r1>

common/source/docs/common-stellarf4.rst

@@ -0,0 +1,110 @@
+.. _common-stellarf4:
+[copywiki destination="plane,copter,rover,blimp"]
+===========================
+StellarF4 Flight Controller
+===========================
+StellarF4 is an autopilot by `Stingbee <https://stingbee.com.ua/flight_controllers/stellarf4>`__.
+
+Features
+========
+
+* Processor
+   *  STM32F405
+* Sensors
+   *  ICM-42688p/BMI270 Acc/Gyro
+   *  DPS310/BMP280 barometer
+   *  AT7456E OSD
+   *  W25Q128 dataflash
+* Power
+   *  2S-6S Lipo input voltage with voltage monitoring
+   *  12V, 3A BEC for powering Video Transmitter
+   *  5V, 2A BEC for internal and peripherals
+* Interfaces
+   *  10x PWM outputs DShot capable, PWM1-4 DShot capable
+   *  6x UARTs
+   *  1x I2C
+   *  2x ADC
+   *  SPI flash for logging
+   *  USB-C port
+* LED
+   *  Red, 3.3V power indicator
+   *  Green, FC status
+* Size
+   *  41 x 41mm PCB with 30.5mm M3 mounting
+
+Pinout
+======
+
+.. image:: ../../../images/StellarF4-top.png
+   :target: ../_images/StellarF4-top.png
+
+.. image:: ../../../images/StellarF4-bot.png
+   :target: ../_images/StellarF4-bot.png
+
+UART Mapping
+============
+The UARTs are marked RXn and TXn in the above pinouts. The RXn pin is the
+receive pin for UARTn. The TXn pin is the transmit pin for UARTn.
+
+- SERIAL0 -> USB
+- SERIAL1 -> USART1 (DJI / VTX, DMA capable)
+- SERIAL2 -> USART2 (Serial RC input, DMA capable)
+- SERIAL3 -> USART3 (User) (NO DMA)
+- SERIAL4 -> UART4 (User) (NO DMA)
+- SERIAL5 -> UART5 (ESC Telemetry) (NO DMA)
+- SERIAL6 -> USART6 (GPS) (NO DMA)
+
+RC Input
+========
+The default RC input is configured on the UART2(SERIAL1) RX2 input and can be used for all ArduPilot supported unidirectional receiver protocols except PPM.
+
+* SBUS/DSM/SRXL connects to the RX2 pin.
+* CRSF also requires a TX2 connection, in addition to RX2, and automatically provides telemetry.
+* FPort requires connection to TX2 and :ref:`SERIAL1_OPTIONS<SERIAL1_OPTIONS>` set to "7". See :ref:`common-FPort-receivers`.
+* SRXL2 requires a connection to TX2 and automatically provides telemetry. Set :ref:`SERIAL1_OPTIONS<SERIAL1_OPTIONS>` to “4”.
+
+OSD Support
+===========
+StellarF4 supports using its internal OSD using OSD_TYPE 1 (MAX7456 driver).
+External OSD support such as DJI or DisplayPort can be used simultaneously and is preconfigured on SERIAL3 but can be supported on any spare UART. See :ref:`common-msp-osd-overview-4.2` for more info.
+
+PWM Output
+==========
+StellarF4 supports up to 10 PWM/Dshot outputs. PWM1-4 outputs support Bi-Directional DShot.
+
+Channels 1-4 support bi-directional DShot. Channels 1-8 marked as M1-M8 on the board. Channels 9-10 marked as S1-S2 on the board. PWM outputs are grouped and every group must use the same output protocol:
+
+
+* 1, 2, 3, 4  are Group 1;
+* 5, 6, 7, 8  are Group 2;
+* 9           is Group 3;
+* 10           is Group 4;
+
+Battery Monitoring
+==================
+The board has 1 built-in voltage divider on an ADC input and 1x current ADC input and supports and external 3.3V based current sensor. The voltage input is compatible with 2~6S LiPo batteries.
+
+The default battery parameters are:
+
+* :ref:`BATT_MONITOR<BATT_MONITOR>` = 4
+* :ref:`BATT_VOLT_PIN<BATT_VOLT_PIN__AP_BattMonitor_Analog>` = 10
+* :ref:`BATT_CURR_PIN<BATT_CURR_PIN__AP_BattMonitor_Analog>` = 11 (CURR pin)
+* :ref:`BATT_VOLT_MULT<BATT_VOLT_MULT__AP_BattMonitor_Analog>` = 11
+* :ref:`BATT_AMP_PERVLT<BATT_AMP_PERVLT__AP_BattMonitor_Analog>` = 52.7
+
+Compass
+=======
+StellarF4 does not have a built-in compass, but you can attach an external compass using I2C on the SDA and SCL pads.
+
+Camera Switch
+=============
+GPIO 81 controls which camera input (CAM1 or CAM2) is applied to the internal OSD. A :ref:`RELAY <common-relay>` function can be enabled to control the switching.
+
+Loading Firmware
+================
+Firmware for these boards can be found at https://firmware.ardupilot.org in sub-folders labeled StellarF4.
+
+Initial firmware load can be done with DFU by plugging in USB with the
+boot button pressed. Then you should load the "ardu*_with_bl.hex" firmware, using your favourite DFU loading tool. eg STM32CubeProgrammer
+
+Subsequently, you can update firmware with Mission Planner.