sen5x_i2c.h

/*
 * THIS FILE IS AUTOMATICALLY GENERATED
 *
 * I2C-Generator: 0.3.0
 * Yaml Version: 2.1.3
 * Template Version: 0.7.0-109-gb259776
 */
/*
 * Copyright (c) 2021, Sensirion AG
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * * Redistributions of source code must retain the above copyright notice, this
 *   list of conditions and the following disclaimer.
 *
 * * Redistributions in binary form must reproduce the above copyright notice,
 *   this list of conditions and the following disclaimer in the documentation
 *   and/or other materials provided with the distribution.
 *
 * * Neither the name of Sensirion AG nor the names of its
 *   contributors may be used to endorse or promote products derived from
 *   this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
 * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 */

#ifndef SEN5X_I2C_H
#define SEN5X_I2C_H

#ifdef __cplusplus
extern "C" {
#endif

#include "sensirion_config.h"

/**
 * sen5x_start_measurement() - Starts a continuous measurement.
 *
 * After starting the measurement, it takes some time (~1s) until the first
 * measurement results are available. You could poll with the command
 * 0x0202 \"Read Data Ready\" to check when the results are ready to read.
 *
 * This command is only available in idle mode. If the device is already
 * in any measure mode, this command has no effect.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_start_measurement(void);

/**
 * sen5x_start_measurement_without_pm() - Starts a continuous measurement
 * without PM. Only humidity, temperature, VOC and NOx are available in this
 * mode. Laser and fan are switched off to keep power consumption low.
 *
 * After starting the measurement, it takes some time (~1s) until the first
 * measurement results are available. You could poll with the command
 * 0x0202 \"Read Data Ready\" to check when the results are ready to read.
 *
 * This command is only available in idle mode. If the device is already
 * in any measure mode, this command has no effect.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_start_measurement_without_pm(void);

/**
 * sen5x_stop_measurement() - Stops the measurement and returns to idle mode.
 *
 * If the device is already in idle mode, this command has no effect.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_stop_measurement(void);

/**
 * sen5x_read_data_ready() - This command can be used to check if new
 * measurement results are ready to read. The data ready flag is automatically
 * reset after reading the measurement values with the 0x03.. \"Read Measured
 * Values\" commands.
 *
 * @note During fan (auto-)cleaning, no measurement data is available for
 * several seconds and thus this flag will not be set until cleaning has
 * finished. So please expect gaps of several seconds at any time if fan
 * auto-cleaning is enabled.
 *
 * @param padding Padding byte, always 0x00.
 *
 * @param data_ready True (0x01) if data is ready, False (0x00) if not. When no
 * measurement is running, False will be returned.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_data_ready(bool* data_ready);

/**
 * sen5x_read_measured_values() - Returns the measured values.

 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data is
 * available at all (e.g. measurement not running for at least one
 * second), all values will be NAN.
 *
 * @param mass_concentration_pm1p0 PM1.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm2p5 PM2.5 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm4p0 PM4.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm10p0 PM10.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param ambient_humidity RH [%]
 * @note If this value is unknown, NAN is returned.
 *
 * @param ambient_temperature  T [°C]
 * @note If this value is unknown, NAN is returned.
 *
 * @param voc_index VOC Index
 * @note If this value is unknown, NAN is returned.
 *
 * @param nox_index NOx Index
 * @note If this value is unknown, NAN is returned. During
 * the first 10..11 seconds after power-on or device reset, this
 * value will be NAN as well.*
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_values(float* mass_concentration_pm1p0,
                                   float* mass_concentration_pm2p5,
                                   float* mass_concentration_pm4p0,
                                   float* mass_concentration_pm10p0,
                                   float* ambient_humidity,
                                   float* ambient_temperature, float* voc_index,
                                   float* nox_index);

/**
 * sen5x_read_measured_values_as_integers() - Returns the measured values
 * without scaling factors applied.
 *
 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data is
 * available at all (e.g. measurement not running for at least one
 * second), all values will be at their upper limit (0xFFFF for `uint16`,
 * 0x7FFF for `int16`).
 *
 * @param mass_concentration_pm1p0 Value is scaled with factor 10:
 *                                 PM1.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm2p5 Value is scaled with factor 10:
 *                                 PM2.5 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm4p0 Value is scaled with factor 10:
 *                                 PM4.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm10p0 Value is scaled with factor 10:
 *                                  PM10.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param ambient_humidity Value is scaled with factor 100: RH [%] = value / 100
 * @note If this value is unknown, 0x7FFF is returned.
 *
 * @param ambient_temperature Value is scaled with factor 200:
 *                            T [°C] = value / 200
 * @note If this value is unknown, 0x7FFF is returned.
 *
 * @param voc_index Value is scaled with factor 10: VOC Index = value / 10
 * @note If this value is unknown, 0x7FFF is returned.
 *
 * @param nox_index Value is scaled with factor 10: NOx Index = value / 10
 * @note If this value is unknown, 0x7FFF is returned. During
 * the first 10..11 seconds after power-on or device reset, this
 * value will be 0x7FFF as well.*
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_values_as_integers(
    uint16_t* mass_concentration_pm1p0, uint16_t* mass_concentration_pm2p5,
    uint16_t* mass_concentration_pm4p0, uint16_t* mass_concentration_pm10p0,
    int16_t* ambient_humidity, int16_t* ambient_temperature, int16_t* voc_index,
    int16_t* nox_index);

/**
 * sen5x_read_measured_raw_values() - Returns the measured raw values.

 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data
 * is available at all (e.g. measurement not running for at least one
 * second), all values will be at their upper limit (0xFFFF for `uint16`,
 * 0x7FFF for `int16`).
 *
 * @param raw_humidity Value is scaled with factor 100: RH [%] = value / 100
 * @note If this value is unknown, 0x7FFF is returned.
 *
 * @param raw_temperature Value is scaled with factor 200: T [°C] = value / 200
 * @note If this value is unknown, 0x7FFF is returned.
 *
 * @param raw_voc Raw measured VOC ticks without scale factor.
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param raw_nox Raw measured NOx ticks without scale factor.
 * @note If this value is unknown, 0xFFFF is returned. During
 * the first 10..11 seconds after power-on or device reset, this
 * value will be 0xFFFF as well.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_raw_values(int16_t* raw_humidity,
                                       int16_t* raw_temperature,
                                       uint16_t* raw_voc, uint16_t* raw_nox);

/**
 * sen5x_read_measured_values_sen50() - Returns the measured values for SEN50.

 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data is
 * available at all (e.g. measurement not running for at least one
 * second), all values will be NAN.
 *
 * @param mass_concentration_pm1p0 PM1.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm2p5 PM2.5 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm4p0 PM4.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm10p0 PM10.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_values_sen50(float* mass_concentration_pm1p0,
                                         float* mass_concentration_pm2p5,
                                         float* mass_concentration_pm4p0,
                                         float* mass_concentration_pm10p0);

/**
 * sen5x_read_measured_pm_values() - Returns the measured particulate
 * matter values.
 *
 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data
 * is available at all (e.g. measurement not running for at least one
 * second), all values will be NAN.
 *
 * @param mass_concentration_pm1p0 PM1.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm2p5 PM2.5 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm4p0 PM4.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param mass_concentration_pm10p0 PM10.0 [µg/m³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param number_concentration_pm0p5 PM0.5 [#/cm³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param number_concentration_pm1p0 PM1.0 [#/cm³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param number_concentration_pm2p5 PM2.5 [#/cm³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param number_concentration_pm4p0 PM4.0 [#/cm³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param number_concentration_pm10p0 PM10.0 [#/cm³]
 * @note If this value is unknown, NAN is returned.
 *
 * @param typical_particle_size Size [µm]
 * @note If this value is unknown, NAN is returned.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_pm_values(
    float* mass_concentration_pm1p0, float* mass_concentration_pm2p5,
    float* mass_concentration_pm4p0, float* mass_concentration_pm10p0,
    float* number_concentration_pm0p5, float* number_concentration_pm1p0,
    float* number_concentration_pm2p5, float* number_concentration_pm4p0,
    float* number_concentration_pm10p0, float* typical_particle_size);

/**
 * sen5x_read_measured_pm_values_as_integers() - Returns the measured
 * particulate matter values without scaling applied.
 *
 * The command 0x0202 \"Read Data Ready\" can be used to check if new
 * data is available since the last read operation. If no new data is
 * available, the previous values will be returned again. If no data
 * is available at all (e.g. measurement not running for at least one
 * second), all values will be 0xFFFF.
 *
 * @param mass_concentration_pm1p0 Value is scaled with factor 10:
 *                                 PM1.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm2p5 Value is scaled with factor 10:
 * PM2.5 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm4p0 Value is scaled with factor 10:
 *                                 PM4.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param mass_concentration_pm10p0 Value is scaled with factor 10:
 *                                  PM10.0 [µg/m³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param number_concentration_pm0p5 Value is scaled with factor 10:
 *                                   PM0.5 [#/cm³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param number_concentration_pm1p0 Value is scaled with factor 10:
 *                                   PM1.0 [#/cm³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param number_concentration_pm2p5 Value is scaled with factor 10:
 *                                   PM2.5 [#/cm³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param number_concentration_pm4p0 Value is scaled with factor 10:
 *                                   PM4.0 [#/cm³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param number_concentration_pm10p0 Value is scaled with factor 10:
 *                                    PM10.0 [#/cm³] = value / 10
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @param typical_particle_size Value is scaled with factor 1000:
 *                              Size [µm] = value / 1000
 * @note If this value is unknown, 0xFFFF is returned.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_measured_pm_values_as_integers(
    uint16_t* mass_concentration_pm1p0, uint16_t* mass_concentration_pm2p5,
    uint16_t* mass_concentration_pm4p0, uint16_t* mass_concentration_pm10p0,
    uint16_t* number_concentration_pm0p5, uint16_t* number_concentration_pm1p0,
    uint16_t* number_concentration_pm2p5, uint16_t* number_concentration_pm4p0,
    uint16_t* number_concentration_pm10p0, uint16_t* typical_particle_size);

/**
 * sen5x_start_fan_cleaning() - Starts the fan cleaning manually. The \"data
 * ready\"-flag will be cleared immediately and during the next few seconds, no
 * new measurement results will be available (old values will be returned). Once
 * the cleaning is finished, the \"data ready\"-flag will be set and new
 * measurement results will be available.
 *
 * When executing this command while cleaning is already active, the
 * command does nothing.
 *
 * If you stop the measurement while fan cleaning is active, the cleaning
 * will be aborted immediately.
 *
 * @note This command is only available in measure mode with PM measurement
 * enabled, i.e. only if the fan is already running. In any other state, this
 * command does nothing.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_start_fan_cleaning(void);

/**
 * sen5x_set_temperature_offset_simple() - Sets the temperature offset parameter
 * in degrees celsius for the device, while leaving the other parameters at
 * their default setting.
 *
 * @param temp_offset Constant temperature offset in degrees celsius.
 * The default value is 0.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_temperature_offset_simple(float temp_offset);

/**
 * sen5x_get_temperature_offset_simple() - Gets the temperature offset parameter
 * in degrees celsius from the device.
 *
 * @note The other parameters, such as slope and time constant may differ
 * from the default values, if they were previously set using
 * `setTemperatureOffsetParameters`.
 *
 * @param temp_offset Constant temperature offset in degrees celsius.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_temperature_offset_simple(float* temp_offset);

/**
 * sen5x_set_temperature_offset_parameters() - Sets the temperature offset
 * parameters for the device.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param temp_offset Constant temperature offset scaled with factor 200 (T [°C]
 * = value / 200). The default value is 0.
 *
 * @param slope Normalized temperature offset slope scaled with factor 10000
 * (applied factor = value / 10000). The default value is 0.
 *
 * @param time_constant Time constant [s] how fast the new slope and offset will
 * be applied. After the specified value in seconds, 63% of the new slope and
 * offset are applied. A time constant of zero means the new values will be
 * applied immediately (within the next measure interval of 1 second).
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_temperature_offset_parameters(int16_t temp_offset,
                                                int16_t slope,
                                                uint16_t time_constant);

/**
 * sen5x_get_temperature_offset_parameters() - Gets the temperature offset
 * parameters from the device.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param temp_offset Constant temperature offset scaled with factor 200 (T [°C]
 * = value / 200).
 *
 * @param slope Normalized temperature offset slope scaled with factor 10000
 * (applied factor = value / 10000).
 *
 * @param time_constant Time constant [s] how fast the slope and offset are
 * applied. After the specified value in seconds, 63% of the new slope and
 * offset are applied.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_temperature_offset_parameters(int16_t* temp_offset,
                                                int16_t* slope,
                                                uint16_t* time_constant);

/**
 * sen5x_set_warm_start_parameter() - Sets the warm start parameter for the
 * device.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @note This parameter can be changed in any state of the device (and the
 * getter immediately returns the new value), but it is applied only the next
 * time starting a measurement, i.e. when sending a \"Start Measurement\"
 * command! So the parameter needs to be set *before* a warm-start measurement
 * is started.
 *
 * @param warm_start Warm start behavior as a value in the range from 0 (cold
 * start) to 65535 (warm start). The default value is 0.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_warm_start_parameter(uint16_t warm_start);

/**
 * sen5x_get_warm_start_parameter() - Gets the warm start parameter from the
 * device.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param warm_start Warm start behavior as a value in the range from 0 (cold
 * start) to 65535 (warm start).
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_warm_start_parameter(uint16_t* warm_start);

/**
 * sen5x_set_voc_algorithm_tuning_parameters() - Sets the tuning parameters of
 * the VOC algorithm.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @note This command is available only in idle mode. In measure mode, this
 * command has no effect. In addition, it has no effect if at least one
 * parameter is outside the specified range.
 *
 * @param index_offset VOC index representing typical (average) conditions.
 * Allowed values are in range 1..250. The default value is 100.
 *
 * @param learning_time_offset_hours Time constant to estimate the VOC algorithm
 * offset from the history in hours. Past events will be forgotten after about
 * twice the learning time. Allowed values are in range 1..1000. The default
 * value is 12 hours.
 *
 * @param learning_time_gain_hours Time constant to estimate the VOC algorithm
 * gain from the history in hours. Past events will be forgotten after about
 * twice the learning time. Allowed values are in range 1..1000. The default
 * value is 12 hours.
 *
 * @param gating_max_duration_minutes Maximum duration of gating in minutes
 * (freeze of estimator during high VOC index signal). Set to zero to disable
 * the gating. Allowed values are in range 0..3000. The default value is 180
 * minutes.
 *
 * @param std_initial Initial estimate for standard deviation. Lower value
 * boosts events during initial learning period, but may result in larger
 * device-to-device variations. Allowed values are in range 10..5000. The
 * default value is 50.
 *
 * @param gain_factor Gain factor to amplify or to attenuate the VOC index
 * output. Allowed values are in range 1..1000. The default value is 230.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_voc_algorithm_tuning_parameters(
    int16_t index_offset, int16_t learning_time_offset_hours,
    int16_t learning_time_gain_hours, int16_t gating_max_duration_minutes,
    int16_t std_initial, int16_t gain_factor);

/**
 * sen5x_get_voc_algorithm_tuning_parameters() - Gets the currently set tuning
 * parameters of the VOC algorithm.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param index_offset VOC index representing typical (average) conditions.
 *
 * @param learning_time_offset_hours Time constant to estimate the VOC algorithm
 * offset from the history in hours. Past events will be forgotten after about
 * twice the learning time.
 *
 * @param learning_time_gain_hours Time constant to estimate the VOC algorithm
 * gain from the history in hours. Past events will be forgotten after about
 * twice the learning time.
 *
 * @param gating_max_duration_minutes Maximum duration of gating in minutes
 * (freeze of estimator during high VOC index signal). Zero disables the gating.
 *
 * @param std_initial Initial estimate for standard deviation. Lower value
 * boosts events during initial learning period, but may result in larger
 * device-to-device variations.
 *
 * @param gain_factor Gain factor to amplify or to attenuate the VOC index
 * output.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_voc_algorithm_tuning_parameters(
    int16_t* index_offset, int16_t* learning_time_offset_hours,
    int16_t* learning_time_gain_hours, int16_t* gating_max_duration_minutes,
    int16_t* std_initial, int16_t* gain_factor);

/**
 * sen5x_set_nox_algorithm_tuning_parameters() - Sets the tuning parameters of
 * the NOx algorithm.
 *
 * Supported sensors: SEN55
 *
 * @note This command is available only in idle mode. In measure mode, this
 * command has no effect. In addition, it has no effect if at least one
 * parameter is outside the specified range.
 *
 * @param index_offset NOx index representing typical (average) conditions.
 * Allowed values are in range 1..250. The default value is 1.
 *
 * @param learning_time_offset_hours Time constant to estimate the NOx algorithm
 * offset from the history in hours. Past events will be forgotten after about
 * twice the learning time. Allowed values are in range 1..1000. The default
 * value is 12 hours.
 *
 * @param learning_time_gain_hours The time constant to estimate the NOx
 * algorithm gain from the history has no impact for NOx. This parameter is
 * still in place for consistency reasons with the VOC tuning parameters
 * command. This parameter must always be set to 12 hours.
 *
 * @param gating_max_duration_minutes Maximum duration of gating in minutes
 * (freeze of estimator during high NOx index signal). Set to zero to disable
 * the gating. Allowed values are in range 0..3000. The default value is 720
 * minutes.
 *
 * @param std_initial The initial estimate for standard deviation parameter has
 * no impact for NOx. This parameter is still in place for consistency reasons
 * with the VOC tuning parameters command. This parameter must always be set
 * to 50.
 *
 * @param gain_factor Gain factor to amplify or to attenuate the NOx index
 * output. Allowed values are in range 1..1000. The default value is 230.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_nox_algorithm_tuning_parameters(
    int16_t index_offset, int16_t learning_time_offset_hours,
    int16_t learning_time_gain_hours, int16_t gating_max_duration_minutes,
    int16_t std_initial, int16_t gain_factor);

/**
 * sen5x_get_nox_algorithm_tuning_parameters() - Gets the currently set tuning
 * parameters of the NOx algorithm.
 *
 * Supported sensors: SEN55
 *
 * @param index_offset NOx index representing typical (average) conditions.
 *
 * @param learning_time_offset_hours Time constant to estimate the NOx algorithm
 * offset from the history in hours. Past events will be forgotten after about
 * twice the learning time.
 *
 * @param learning_time_gain_hours The time constant to estimate the NOx
 * algorithm gain from the history has no impact for NOx. This parameter is
 * still in place for consistency reasons with the VOC tuning parameters
 * command.
 *
 * @param gating_max_duration_minutes Maximum duration of gating in minutes
 * (freeze of estimator during high NOx index signal). Zero disables the gating.
 *
 * @param std_initial The initial estimate for standard deviation has no impact
 * for NOx. This parameter is still in place for consistency reasons with the
 * VOC tuning parameters command.
 *
 * @param gain_factor Gain factor to amplify or to attenuate the NOx index
 * output.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_nox_algorithm_tuning_parameters(
    int16_t* index_offset, int16_t* learning_time_offset_hours,
    int16_t* learning_time_gain_hours, int16_t* gating_max_duration_minutes,
    int16_t* std_initial, int16_t* gain_factor);

/**
 * sen5x_set_rht_acceleration_mode() - Sets the RH/T acceleration mode.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @note This parameter can be changed in any state of the device (and the
 * getter immediately returns the new value), but it is applied only the next
 * time starting a measurement, i.e. when sending a \"Start Measurement\"
 * command. So the parameter needs to be set *before* a new measurement is
 * started.
 *
 * @param mode The new RH/T acceleration mode.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_rht_acceleration_mode(uint16_t mode);

/**
 * sen5x_get_rht_acceleration_mode() - Gets the RH/T acceleration mode.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param mode The current RH/T acceleration mode.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_rht_acceleration_mode(uint16_t* mode);

/**
 * sen5x_set_voc_algorithm_state() - Sets the VOC algorithm state previously
 * received with the \"Get VOC Algorithm State\" command.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @note This command is only available in idle mode and the state will be
 * applied only once when starting the next measurement. Any further
 * measurements (i.e. when stopping and restarting the measure mode) will reset
 * the state to initial values. In measure mode, this command has no effect.
 *
 * @param state VOC algorithm state to restore.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_voc_algorithm_state(const uint8_t* state, uint8_t state_size);

/**
 * sen5x_get_voc_algorithm_state() - Gets the current VOC algorithm state. This
 * data can be used to restore the state with the \"Set VOC Algorithm State\"
 * command after a short power cycle or device reset.
 *
 * This command can be used either in measure mode or in idle mode
 * (which will then return the state at the time when the measurement
 * was stopped). In measure mode, the state can be read each measure
 * interval to always have the latest state available, even in case of
 * a sudden power loss.
 *
 * Supported sensors: SEN54, SEN55
 *
 * @param state Current VOC algorithm state.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_voc_algorithm_state(uint8_t* state, uint8_t state_size);

/**
 * sen5x_set_fan_auto_cleaning_interval() - Sets the fan auto cleaning interval
 * for the device.
 *
 * @param interval Fan auto cleaning interval [s]. Set to zero to disable auto
 * cleaning.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_set_fan_auto_cleaning_interval(uint32_t interval);

/**
 * sen5x_get_fan_auto_cleaning_interval() - Gets the fan auto cleaning interval
 * from the device.
 *
 * @param interval Fan auto cleaning interval [s]. Zero means auto cleaning is
 * disabled.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_fan_auto_cleaning_interval(uint32_t* interval);

/**
 * sen5x_get_product_name() - Gets the product name from the device.
 *
 * @param product_name Null-terminated ASCII string containing the product name.
 * Up to 32 characters can be read from the device.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_product_name(unsigned char* product_name,
                               uint8_t product_name_size);

/**
 * sen5x_get_serial_number() - Gets the serial number from the device.
 *
 * @param serial_number Null-terminated ASCII string containing the serial
 * number. Up to 32 characters can be read from the device.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_serial_number(unsigned char* serial_number,
                                uint8_t serial_number_size);

/**
 * sen5x_get_version() - Gets the version information for the hardware, firmware
 * and communication protocol.
 *
 * @param firmware_major Firmware major version number.
 *
 * @param firmware_minor Firmware minor version number.
 *
 * @param firmware_debug Firmware debug state. If the debug state is set, the
 * firmware is in development.
 *
 * @param hardware_major Hardware major version number.
 *
 * @param hardware_minor Hardware minor version number.
 *
 * @param protocol_major Protocol major version number.
 *
 * @param protocol_minor Protocol minor version number.
 *
 * @param padding Padding byte, ignore this.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_get_version(uint8_t* firmware_major, uint8_t* firmware_minor,
                          bool* firmware_debug, uint8_t* hardware_major,
                          uint8_t* hardware_minor, uint8_t* protocol_major,
                          uint8_t* protocol_minor);

/**
 * sen5x_read_device_status() - Reads the current device status.
 *
 * Use this command to get detailed information about the device status.
 * The device status is encoded in flags. Each device status flag
 * represents a single bit in a 32-bit integer value. If more than one
 * error is present, the device status register value is the sum of the
 * corresponding flag values. For details about the available flags,
 * refer to the device status flags documentation.
 *
 * @note The status flags of type \"Error\" are sticky, i.e. they are not
 * cleared automatically even if the error condition no longer exists. So they
 * can only be cleared manually with the command 0xD210 \"Read And Clear Device
 * Status\" or with a device reset. All other flags are not sticky, i.e. they
 * are cleared automatically if the trigger condition disappears.
 *
 * @param device_status Device status (32 flags as an integer value). For
 * details, please refer to the device status flags documentation.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_device_status(uint32_t* device_status);

/**
 * sen5x_read_and_clear_device_status() - Reads the current device status (like
 * command 0xD206 \"Read Device Status\") and afterwards clears all flags.
 *
 * @param device_status Device status (32 flags as an integer value) **before**
 * clearing it. For details, please refer to the device status flags
 * documentation.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_read_and_clear_device_status(uint32_t* device_status);

/**
 * sen5x_device_reset() - Executes a reset on the device. This has the same
 * effect as a power cycle.
 *
 * @return 0 on success, an error code otherwise
 */
int16_t sen5x_device_reset(void);

#ifdef __cplusplus
}
#endif

#endif /* SEN5X_I2C_H */