hallcurrent9

---

Hall Current 9 Click

Hall Current 9 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Nenad Filipovic
• Date : Dec 2020.
• Type : I2C type

Software Support

Example Description

This library contains API for Hall Current 9 Click driver. The library contains drivers for measuring ADC values and for calculation current.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.HallCurrent9

Example Key Functions

• hallcurrent9_cfg_setup Config Object Initialization function.

void hallcurrent9_cfg_setup ( hallcurrent9_cfg_t *cfg );

• hallcurrent9_init Initialization function.

err_t hallcurrent9_init ( hallcurrent9_t *ctx, hallcurrent9_cfg_t *cfg );

• hallcurrent9_default_cfg Click Default Configuration function.

void hallcurrent9_default_cfg ( hallcurrent9_t *ctx );

• hallcurrent9_read_adc Hall Current 9 I2C ADC reading function.

err_t hallcurrent9_read_adc ( hallcurrent9_t *ctx, uint16_t *read_adc );

• hallcurrent9_set_calibration Hall Current 9 set calibration function.

err_t hallcurrent9_set_calibration ( hallcurrent9_t *ctx, hallcurrent9_calibration_data_t *adc_val );

• hallcurrent9_get_current Hall Current 9 get current function.

float hallcurrent9_get_current ( hallcurrent9_t *ctx, hallcurrent9_calibration_data_t *adc_val );

Application Init

Initializes I2C driver and triggers the built-in calibration.

void application_init ( void ) 
{
    log_cfg_t log_cfg;                    /**< Logger config object. */
    hallcurrent9_cfg_t hallcurrent9_cfg;  /**< Click config object.  */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_printf( &logger, "\r\n" );
    log_printf( &logger, "--------------------------\r\n" );
    log_printf( &logger, "   Hall Current 9 Click   \r\n" );
    log_printf( &logger, "--------------------------\r\n" );
    log_info( &logger, " Application Init " );

    // Click initialization.

    hallcurrent9_cfg_setup( &hallcurrent9_cfg );
    HALLCURRENT9_MAP_MIKROBUS( hallcurrent9_cfg, MIKROBUS_1 );
    err_t init_flag = hallcurrent9_init( &hallcurrent9, &hallcurrent9_cfg );
    if ( init_flag == I2C_MASTER_ERROR ) {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }
    
    log_printf( &logger, "---------------------------\r\n" );
    log_printf( &logger, "        Calibration        \r\n" );
    log_printf( &logger, "- - - - - - - - - - - - - -\r\n" );
    log_printf( &logger, "> Turn OFF the Power unit <\r\n" );
    log_printf( &logger, "- - - - - - - - - - - - - -\r\n" );
    log_printf( &logger, "  In the following 5 sec.  \r\n" );
    log_printf( &logger, " turn OFF the Power Supply \r\n" );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    
    log_printf( &logger, "-------------------------\r\n" );
    log_printf( &logger, "    Start calibration    \r\n" );
    
    if ( hallcurrent9_set_calibration( &hallcurrent9, &avg_adc_data ) == HALLCURRENT9_OK ) {
        log_printf( &logger, "---------------------------\r\n" );
        log_printf( &logger, "    Calibration  Done    \r\n" );
        Delay_ms ( 1000 );    
    }
    
    log_printf( &logger, "---------------------------\r\n" );
    log_printf( &logger, "    Start measurements :   \r\n" );
    log_printf( &logger, "---------------------------\r\n" );
}

Application Task

This is an example that demonstrates the use of the Hall Current 9 Click board. In this example, we read and display the ADC and current ( mA ) data. Results are being sent to the Usart Terminal where you can track their changes.

void application_task ( void ) 
{   
    log_printf( &logger, "--------------------------\r\n", adc_data );
    hallcurrent9_read_adc( &hallcurrent9, &adc_data );
    log_printf( &logger, "   ADC     : %d \r\n", adc_data );

    current = hallcurrent9_get_current( &hallcurrent9, &avg_adc_data );
    log_printf( &logger, "   Current : %.2f mA \r\n", current );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---