magneticrotary3

---

Magnetic Rotary 3 Click

Magnetic Rotary 3 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Stefan Filipovic
• Date : May 2022.
• Type : SPI type

Software Support

Example Description

This example demonstrates the use of Magnetic Rotary 3 Click board by reading and displaying the magnet's angular position in degrees.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.MagneticRotary3

Example Key Functions

• magneticrotary3_cfg_setup Config Object Initialization function.

void magneticrotary3_cfg_setup ( magneticrotary3_cfg_t *cfg );

• magneticrotary3_init Initialization function.

err_t magneticrotary3_init ( magneticrotary3_t *ctx, magneticrotary3_cfg_t *cfg );

• magneticrotary3_write_register This function writes a desired data to the selected register by using SPI serial interface.

err_t magneticrotary3_write_register ( magneticrotary3_t *ctx, uint16_t reg, uint16_t data_in );

• magneticrotary3_read_register This function reads data from the selected register by using SPI serial interface.

err_t magneticrotary3_read_register ( magneticrotary3_t *ctx, uint16_t reg, uint16_t *data_out );

• magneticrotary3_get_angle This function reads the absolute position raw data and converts it to degrees (Angle).

err_t magneticrotary3_get_angle ( magneticrotary3_t *ctx, float *angle );

Application Init

Initializes the driver and logger.

void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    magneticrotary3_cfg_t magneticrotary3_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    magneticrotary3_cfg_setup( &magneticrotary3_cfg );
    MAGNETICROTARY3_MAP_MIKROBUS( magneticrotary3_cfg, MIKROBUS_1 );
    if ( SPI_MASTER_ERROR == magneticrotary3_init( &magneticrotary3, &magneticrotary3_cfg ) )
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }
    
    log_info( &logger, " Application Task " );
}

Application Task

Reads the magnet's angular position in degrees every 100ms and displays the results on the USB UART.

void application_task ( void )
{
    float angle;
    if ( MAGNETICROTARY3_OK == magneticrotary3_get_angle ( &magneticrotary3, &angle ) )
    {
        log_printf( &logger, " Angle: %.1f degrees\r\n\n", angle );
        Delay_ms ( 100 );
    }
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---