thermo2

---

Thermo 2 Click

Thermo 2 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Stefan Filipovic
• Date : Feb 2022.
• Type : PWM type

Software Support

Example Description

This example demonstrates the use of Thermo 2 Click board by reading and displaying the temperature in Celsius.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.Thermo2

Example Key Functions

• thermo2_cfg_setup Config Object Initialization function.

void thermo2_cfg_setup ( thermo2_cfg_t *cfg );

• thermo2_init Initialization function.

err_t thermo2_init ( thermo2_t *ctx, thermo2_cfg_t *cfg );

• thermo2_default_cfg Click Default Configuration function.

err_t thermo2_default_cfg ( thermo2_t *ctx );

• thermo2_write_scratchpad This function writes the temperature thresholds and configuration byte to the scratchpad.

err_t thermo2_write_scratchpad ( thermo2_t *ctx, uint8_t temp_high, uint8_t temp_low, uint8_t config );

• thermo2_read_scratchpad This function reads the scratchpad bytes.

err_t thermo2_read_scratchpad ( thermo2_t *ctx, uint8_t *scratchpad );

• thermo2_read_temperature This function reads the temperature value in Celsius.

err_t thermo2_read_temperature ( thermo2_t *ctx, float *temperature );

Application Init

Initializes the driver and performs the Click default configuration.

void application_init ( void )
{
    log_cfg_t log_cfg;  /**< Logger config object. */
    thermo2_cfg_t thermo2_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.
    thermo2_cfg_setup( &thermo2_cfg );
    THERMO2_MAP_MIKROBUS( thermo2_cfg, MIKROBUS_1 );
    if ( ONE_WIRE_ERROR == thermo2_init( &thermo2, &thermo2_cfg ) )
    {
        log_error( &logger, " Communication init." );
        for ( ; ; );
    }
    
    if ( THERMO2_ERROR == thermo2_default_cfg ( &thermo2 ) )
    {
        log_error( &logger, " Default configuration." );
        for ( ; ; );
    }
    
    log_info( &logger, " Application Task " );
}

Application Task

Reads and displays the temperature measured by the Click board on the USB UART approximately every 800ms as this matches the required conversion time for 12-bit temperature resolution.

void application_task ( void )
{
    float temperature;
    if ( THERMO2_OK == thermo2_read_temperature ( &thermo2, &temperature ) )
    {
        log_printf( &logger, " Temperature: %.2f C\r\n\n", temperature );
    }
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---