[Support]:

[ZacTyAdams]

Describe the problem you are having

Unable to view color picker screen in HomeAssistant Add-on

Version

latest

Swatch config file

# REQUIRED: Define a list of objects that are expected to be seen. These can be specific
# to one camera or common between many / all cameras
objects:
  # REQUIRED: Name of the object
  fireplace:
    # REQUIRED: the list of color variants that this object can be detected as. Useful for
    # different lighting conditions
    color_variants:
      # REQUIRED: the name of the color variant
      default:
        # REQUIRED: the lower R, G, B values that are considered a potential match for the
        # color variant of the object.
        color_lower: 70, 70, 0
        # REQUIRED: the upper R, G, B values that are considered a potential match for the
        # color variant of the object.
        color_upper: 110, 100, 50
        # OPTIONAL: the time range for when this color variant is allowed
        # NOTE: make sure that /etc/localtime is passed to the container so it has valid time
        time_range:
          # OPTIONAL: Color variant is valid if current time is > this 24H time (Default: shown below).
          after: "00:00"
          # OPTIONAL: Color variant is valid if current time is < this 24H time (Default: shown below).
          before: "24:00"
    # OPTIONAL: the min area of the bounding box around groups of matching R, G, B pixels
    # considered a true positive. This is not recommended to be set as a super small amount
    # could be a false positive. (Default: shown below)
    min_area: 1000
    # OPTIONAL: the max area of the bounding box around groups of pixels with R, G, B
    # values within the bounds to be considered a true positive (Default: shown below).
    max_area: 100000
    # OPTIONAL: the min ratio of width/height of bounding box for valid object detection (default: shown below).
    min_ratio:
      0
      # OPTIONAL: the max ratio of width/height of bounding box for valid object detection (default: shown below).
    max_ratio: 24000000

# REQUIRED: Define list of cameras that will be used for color detection.
cameras:
  # REQUIRED: Name of the camera
  living_room_cam:
    # OPTIONAL: Frequency in seconds to run detection on the camera.
    # a value of 0 disables auto detection (Default: shown below).
    auto_detect: 0
    # OPTIONAL: Configure the url and retention of snapshots. (Default: Shown Below)
    snapshot_config:
      # OPTIONAL: but highly recommended, setting the default url for a snapshot to be
      # processed by this camera. This is required for auto detection (Default: none).
      url: "https://wallpaperset.com/w/full/0/d/5/183330.jpg"
      # OPTIONAL: Whether or not to draw bounding boxes for confirmed objects in the snapshots (Default: shown below).
      bounding_box: true
      # OPTIONAL: Whether or not to save a clean png of the snapshot along with the annotated jpg (Default: shown below).
      clean_snapshot: true
      # OPTIONAL: Whether or not to save the snapshots of confirmed detections (Default: shown below).
      save_detections: true
      # OPTIONAL: Whether or not to save the snapshots of missed detections (Default: shown below).
      save_misses: false
      # OPTIONAL: Variations of snapshots to keep. Options are all, mask, crop (Default: shown below).
      mode: "all"
      # OPTIONAL: Number of days of snapshots to keep (Default: shown below).
      retain_days: 7
    # REQUIRED: Zones are cropped areas where the object can be expected to be.
    # This makes searching / matches for efficient and more predictable than searching
    # the entire image.
    zones:
      # REQUIRED: Name of the zone.
      street:
        # REQUIRED: Coordinates to crop the zone by.
        # NOTE: The order of the coordinates are: x, y, x+w, y+h starting in the top left corner as 0, 0.
        coordinates: 225, 540, 350, 620
        # REQUIRED: List of objects that may be in this zone. These correspond to
        # the objects list defined previously and are matched by name.
        objects:
          - fireplace

Relevant log output

[2023-11-08 20:53:18,833]: INFO - Starting SwatchApp
[2023-11-08 20:53:18,838]: INFO - Importing SwatchApp Config
[2023-11-08 20:53:18,838]: INFO - Verified SwatchApp Config
Starting migrations
[2023-11-08 20:53:18,842]: INFO - Starting migrations
There is nothing to migrate
[2023-11-08 20:53:18,846]: INFO - There is nothing to migrate
[2023-11-08 20:53:18,846]: INFO - Starting snapshot cleanup
[2023-11-08 20:53:18,847]: INFO - Starting Detection Cleanup

Any other information that may be helpful

Dashboard view:

Color picker view:

Settings view:

Setting a source via the UI doesn't seem to do anything.

[NickM-27]

what type of url are you using?

[ZacTyAdams]

That URL is just to a dummy wallpaper image I found. This problem is also present when using an actual jpg snapshot URL from the Docker-Wyze-Bridge addon

[NickM-27]

What image url are you entering into the text field in the webUI?

[ZacTyAdams]

In the above photos:
https://wallpaperset.com/w/full/0/d/5/183330.jpg

[SupremeSports]

Same issue here...

[JmanT-glitch]

Same issue here as well

[jmadden91]

Same issue

[frankyman88]

Same issue with a scrypted webhook, using container version 3.1.0 because latest won't launch for me