kcnf

menu LWIP
	choice
	prompt "version"
		config LWIP_ESP
			bool "LWIP espressif sources (close to v1.4.0RC2)"
		config LWIP_GIT
			bool "LWIP (git-pre-1.5, experimental)"
	endchoice
endmenu

menu Hacks

config ESP8266_NEED_ESPCONN_INIT
bool "SDK >= 1.0 fix"
default n

endmenu

menu "Services to build"

config SERVICE_DHCPS
bool "DHCP Server"
help
	You should execute 'resetenv' and reboot again after flashing, if you change this setting.

config SERVICE_TCP
bool "TCP/IP services"

config SERVICE_TELNET
bool "Telnet Service"
depends on SERVICE_TCP

config SERVICE_ECHO
bool "Echo Service"
depends on SERVICE_TCP

endmenu

menu "Modules to build"

config CMD_IW
bool "Wireless commands"

config CMD_PHY
bool "Wireless hardware commands"

config CMD_UART
bool "UART commands"

config CMD_IF
bool "ifconfig/apconfig"

config CMD_GPIO
bool "GPIO commands"

config CMD_FLASH
bool "FLASH commands"

config CMD_LISTEN
bool "Listen on a port"
depends on SERVICE_TCP

config CMD_SEND
bool "Send data over TCP"
depends on SERVICE_TCP

config CMD_NSLOOKUP
bool "Network tool: nslookup"

#seems broken because of undefined reference
#config CMD_PING
#bool "Network tool: ping"

config CMD_TFTP
bool "TFTP firmware update support"

if CMD_TFTP

config ENV_DEFAULT_TFTP_SERVER_IP
string "Default IP to connect to when using tftp command"
default "192.168.1.215"

config ENV_DEFAULT_TFTP_SERVER_DIR
string "TFTP server directory"
default "/"

config ENV_DEFAULT_TFTP_SERVER_FILE
string "TFTP server file to retrieve"
default "antares.com"

endif

config CMD_AT
bool "AT to say OK"

config CMD_ADC
bool "System ADC support"

menuconfig CMD_I2C
bool "I2C subsystem (experimental)"

if CMD_I2C

config CMD_I2C_BMP180
bool "BMP180 pressure sensor"

config CMD_I2C_SHT21
bool "SHT21 humidity sensor"

config CMD_I2C_BH1750
bool "BH1750 light sensor"

config CMD_I2C_SI7020
bool "SI7020 Temperature/Humidity sensor"

config CMD_I2C_PCF8591
bool "PCF8591 8-bit ADC DAC"

config CMD_I2C_INA219
bool "INA219 current sensor"

config CMD_I2C_TCS3414CS
bool "TCS3414CS color sensor (EXPERIMENTAL)"

config CMD_I2C_MLX90614
bool "MLX90614 temperature sensor (EXPERIMENTAL)"

config CMD_I2C_HMC5883L
bool "HMC5883l 3-Axis Digital Compass (Needs testing)"

endif

menuconfig CMD_DHT22
bool "DHT22/DHT11 temperature and humidity sensor"

config ENABLE_MQTT
bool "MQTT Support"

config ENABLE_SCHED
bool "Scheduled command execution"

# Not working right now.
#config ENABLE_PASSTHROUGH
#bool "enable tcp(10101)<->serial passthrough"

menuconfig CMD_DS18B20
bool "DS18B20/DS18S20 Thermal Sensor support"

if CMD_DS18B20
config CMD_DS18B20_DEBUG
bool "DS18B20 Debugging"
help
	Show debugging messages

endif

endmenu

menu "Commandline fine-tuning"

config MICRORL_USE_COMPLETE
bool "Command auto-completion"

config MICRORL_USE_HISTORY
bool "Command history"

endmenu

menu "Environment Settings"

config ENV_OFFSET
hex "Environment address in flash (4K aligned)"
default 0x7c000

config ENV_LEN
hex "Environment length"
default 0x1000 

config ADDR_BLOBSETTING1
hex "Adress of blob settings in flash (copy 1)"
default 0x7d000

config ADDR_BLOBSETTING2
hex "Adress of blob settings in flash (copy 2)"
default 0x7e000

config ENV_NOWRITE
bool "Simulate writes of environment data in flash"
default n


menu "Default Values"

choice
prompt "Default wifi mode"
default WIFI_MODE_AP

config WIFI_MODE_AP
bool "Access point"

config WIFI_MODE_STATION
bool "Station mode - (client)"

config WIFI_MODE_SOFTAP
bool "Soft access point mode - (both AP & client)"

config WIFI_MODE_NONE
bool "Wifi initially off"

endchoice

config ENV_DEFAULT_HOSTNAME
string "Hostname at boot"
default "frankenstein"

config ENV_DEFAULT_STATION_IP
string "Station mode IP address at boot"
default "192.168.0.123"

config ENV_DEFAULT_STATION_MASK
string "Station mode IP netmask at boot"
default "255.255.255.0"

config ENV_DEFAULT_STATION_GW
string "Station mode IP gateway address at boot"
default "192.168.0.1"

if WIFI_MODE_STATION
config ENV_DEFAULT_STATION_AUTO_CONNECT
bool "Station mode: automatically attempt to connect on boot"

if ENV_DEFAULT_STATION_AUTO_CONNECT
config ENV_DEFAULT_STATION_AUTO_SSID
string "SSID to automatically attempt connection"

config ENV_DEFAULT_STATION_AUTO_PASSWORD
string "Password to attempt connection"
endif

endif

config ENV_DEFAULT_AP_IP
string "AP mode IP address at boot"
default "192.168.1.1"

config ENV_DEFAULT_AP_MASK
string "AP mode IP netmask at boot"
default "255.255.255.0"

config ENV_DEFAULT_AP_GW
string "AP mode IP gateway at boot"
default "192.168.1.1"

endmenu

config ENABLE_SECOND_UART
bool "Enable the second uart"
default y

config ENABLE_BANNER
bool "Enable the banner message at boot"
default y


endmenu