Firmware update fails to flash, will not "fit"

[kingozone]

Currently running Klipper on Ender 3 V3 SE. Recently updated, and needed to update the Exapnder board. When I try to update it, I get the following error:

biqu@BTT-CB1:/klipper$ make clean
biqu@BTT-CB1:/klipper$ make flash FLASH_DEVICE=0483:df11
Creating symbolic link out/board
Building out/autoconf.h
Compiling out/src/sched.o
Compiling out/src/command.o
Compiling out/src/basecmd.o
Compiling out/src/debugcmds.o
Compiling out/src/initial_pins.o
Compiling out/src/gpiocmds.o
Compiling out/src/stepper.o
Compiling out/src/endstop.o
Compiling out/src/trsync.o
Compiling out/src/dirzctl.o
Compiling out/src/hx711s.o
Compiling out/src/adccmds.o
Compiling out/src/spicmds.o
Compiling out/src/i2ccmds.o
Compiling out/src/buttons.o
Compiling out/src/tmcuart.o
Compiling out/src/neopixel.o
Compiling out/src/pulse_counter.o
Compiling out/src/lcd_st7920.o
Compiling out/src/lcd_hd44780.o
Compiling out/src/spi_software.o
Compiling out/src/thermocouple.o
Compiling out/src/sensor_adxl345.o
Compiling out/src/sensor_angle.o
Compiling out/src/sensor_mpu9250.o
Compiling out/src/sensor_bulk.o
Compiling out/src/stm32/watchdog.o
Compiling out/src/stm32/gpio.o
Compiling out/src/stm32/clockline.o
Compiling out/src/stm32/dfu_reboot.o
Compiling out/src/generic/crc16_ccitt.o
Compiling out/src/generic/armcm_boot.o
Compiling out/src/generic/armcm_irq.o
Compiling out/src/generic/armcm_reset.o
Compiling out/src/../lib/stm32f0/system_stm32f0xx.o
Compiling out/src/generic/timer_irq.o
Compiling out/src/stm32/stm32f0_timer.o
Compiling out/src/stm32/stm32f0.o
Compiling out/src/stm32/gpioperiph.o
Compiling out/src/stm32/stm32f0_adc.o
Compiling out/src/stm32/stm32f0_i2c.o
Compiling out/src/stm32/spi.o
Compiling out/src/stm32/usbfs.o
Compiling out/src/stm32/chipid.o
Compiling out/src/generic/usb_cdc.o
Building out/compile_time_request.o
Version: 25778772
Preprocessing out/src/generic/armcm_link.ld
Linking out/klipper.elf
/usr/lib/gcc/arm-none-eabi/8.3.1/../../../arm-none-eabi/bin/ld: out/klipper.elf section .text' will not fit in region rom'
/usr/lib/gcc/arm-none-eabi/8.3.1/../../../arm-none-eabi/bin/ld: region `rom' overflowed by 10512 bytes
collect2: error: ld returned 1 exit status
make: *** [Makefile:72: out/klipper.elf] Error 1

How can I fix this? I have followed the manual and everytime, I get this error.

[timmit99]

Can you share screenshots of your menuconfig and advanced options please?

[kingozone]

[kingozone]

After buying a second one, I'm getting the same results. Was curious if something was stuck, so I tried a reflash of an ADXL, no problem. Run a make clean, try again for the board, same issue.

[kingozone]

Any ideas?

[yardi83]

I was running into the exact same issue today while trying to update the expander from klipper v0.11XX to v0.12

This settings fixed it for me:
#231

Docs should be updated with this