| Creator | Mod title | Description | Printer compatibility | Last Changed |
|---|---|---|---|---|
| 1-0-R | V2.4 handle | Handle for Voron 2.4 | V2.4 | 2024-01-08T16:38:25+00:00 |
| 120decibell | Side entry exhaust housing | Exhaust housing with dual cover screws and single or dual side... | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Huvud Chain Mount | Huvud rear mount for Clockwork or LGX that supports a cable chain. | V1.8, VT | 2024-01-08T16:38:25+00:00 | |
| 3dpandme | FANnypack zero | Electronics cooling solution for Voron Zero | V0.2, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Thermistor holder zero | Extended thermistor holder for Voron Zero | V0.2, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| 3vilson | V0.1_Skirt_Holes | Skirt with Access Holes from the bottom | V0.2 | 2024-01-08T16:38:25+00:00 |
| V0.1_Skirt_Inlet | Skirt with C14 inlet + New feet to screw into | V0.2 | 2024-01-08T16:38:25+00:00 | |
| 42bios | Corner panel clip w. cable | Corner panel clip with an internal cable path. | V2.4 | 2024-01-08T16:38:25+00:00 |
| Exhaust filter housing - side... | Exhaust filter housing with the G1-8 "thread on the side. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| relay mount | relay-mount for 2x 2 channel relay modules. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| ademuri | Lights, Camera, Voron | A mount for LED strips and Picam for the V0.1 | V0.2 | 2024-01-08T16:38:25+00:00 |
| aeresov | Ballpoint pen spring DIN clips | Assortment of mechanical DIN clips using common ballpoint pen springs. | V2.4r2, VT | 2024-06-19T10:47:27+00:00 |
| cable tie DIN mount | A bracket for cable ties to route cables across DIN rails. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| MeanWell UHP-xxx DIN mount | A bracket for MeanWell UHP series PSU (200, 350 and 500) to mount... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Raspberry Pi DIN mount | A bracket for Raspberry Pi 3/4 to mount it onto DIN rail, along or... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| SKR 1.3/1.4 DIN mount | A bracket for SKR 1.3/1.4 board to mount it onto DIN rail, along or... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| TL filament sensor bracket | A bracket for TL filament sensor to mount near stock spool holder. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Akio | Hidden cable routing z belt cover | Z belt covers that allow hidden cable routing. | V2.4 | 2024-01-08T16:38:25+00:00 |
| al3ph | Analog Timer Mount | A skirt mount for analog timer | V0.2 | 2024-01-08T16:38:25+00:00 |
| Filament Runout Sensor | A simple filament runout sensor | V0.2, V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 | |
| LED Mount | A mount for 10mm LED WS2812 strips | V0.2 | 2024-01-08T16:38:25+00:00 | |
| PL05 Sensor Mount | A mount PL05 inductive sensor | V0.2 | 2024-01-08T16:38:25+00:00 | |
| alanho | BTT PITFT50 v2 Mount | A mount for the BTT PITFT50 v2 Touch Display | V2.4 | 2024-01-08T16:38:25+00:00 |
| albert | IKEA Dioder Led Mount | A mount for the IKEA Dioder LED strip | V2.4 | 2024-01-08T16:38:25+00:00 |
| AlexanderT-Moss | 270 Clamping Hinges | Simple 270 degree hinges that clamp to the front panels instead of... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Andre | Mini Afterburner ADXL345 Mount | Mount for an AXDL345 on the Mini Afterburner | V0.2 | 2024-01-08T16:38:25+00:00 |
| Mini Afterburner Strain Relief | A replacement strain relief for the Mini Afterburner toolhead | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Revo Nozzle Skirt | A Revo nozzle box hidden in a Trident skirt. | VT | 2024-01-08T16:38:25+00:00 | |
| V0 Neopixel Front Bed Mount | A replacement Front Bed Mount with room for a neopixel or dotstar... | V0.2 | 2024-01-08T16:38:25+00:00 | |
| antoinecellerier | DS18B20 Sensor Mount | DS18B20 temperature sensor mount | V0.2 | 2024-01-08T16:38:25+00:00 |
| ardichoke | V0 Long Thumb Nut | Taller thumb nuts for V0 bed | V0.2 | 2024-01-08T16:38:25+00:00 |
| arkeet | Dial test indicator mount | A toolhead mount for a dial test indicator, where the tip is... | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| Magnetic hotend fan cover | A replacement hotend fan cover, held with magnets instead of screws. | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 | |
| MGN12 X-axis | Replaces the dual MGN9H rails with a single MGN12H. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| V0 DC inlet | Skirt inlet for external 24V DC power supply. | V0.2 | 2024-01-08T16:38:25+00:00 | |
| aTinyShellScript | RS PSU DIN Bracket | DIN brackets for MeanWell RS PSUs with 80mm spacing. | V2.4 | 2024-01-08T16:38:25+00:00 |
| AVieira | Universal_Phone_Mount | This mod allows the use of different smartphones or possibly... | V2.4r2 | 2024-01-08T16:38:25+00:00 |
| baccula | Revo Nozzle Holder for v2.4 350 | A remix of Andre's design allowing for skirt storage of 4 E3D Revo... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Backenfutter | Mount for Electreeks Camera | This Mod is a simple "One Piece" mount for the popular Electreeks... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Badnoob | AB-BN Afterburner mod (5015) | Improved Afterburner with 5015 fan | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| AB-BN for Stock Afterburner (4020) | Improved Dragon and Rapido toolhead for stock Afterburner with 4020... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Precision AB Drive | Changes the gearing for the AB drives to improve both resolution... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Baltojikale | LoudOwl aka Stabby | Alternative dual 5015 part cooling fan toolhead for Afterburner | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| beaugalbraith | Nova Printhead | Use Nova Hotend with Afterburner | V2.4 | 2024-01-08T16:38:25+00:00 |
| BladeScraper-Designs | CornerPanel_SpoolHolder | A better supported Spool Holder that mounts to a modified corner... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Horizontal Spool Holder | Based on the stock holder but mounts to the horizontal extrusions. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Microswitch Pod With Connector | Microswitch pod with JST-XH 4-pin connector | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Blamm | LRS-100 DIN mount | DIN rail mount for an extra LRS-100 Power Supply | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| BlueBear | Bowden Fence | A little "fence" to hold the tubes away from the belts. | V0.2 | 2024-01-08T16:38:25+00:00 |
| Deck Panel Backpack | A mounting alternative if you don't want to drill your deck panel | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Clippable Wago 221 Mounts | Mounts for Wago 221 to screw or clip-in on 1515 extrusions | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Ziptie Mount | Clippable Ziptie hooks for 1515 extrusions | V0.2 | 2024-01-08T16:38:25+00:00 | |
| bobbleheed | Filament Runout Sensor | Filament runout sensor that replaces the stock bowden retainer | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Magnetic Panels | Magnetic clips to allow for easy removal and installation of panels | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Boingomw | Wago mount | Smaller 5 port Wago mount that fits parallel to the support rails | V2.4 | 2024-01-08T16:38:25+00:00 |
| Bondtech | Mini-After-LGX-Lite | LGX Lite Toolhead Setup For Voron V0.1. | V0.2 | 2024-01-08T16:38:25+00:00 |
| btp | Galileo chain mount (befenybay) | Modified chain mount position to cater for difference with Galileo... | VSW | 2024-01-08T16:38:25+00:00 |
| buzzdalf | v1.8/2.4 Afterburner connector... | v1.8/2.4 Connector cover for 42STH20-1004AS | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| Ender 3 Switchwire Taller Z Mod | Taller Z Mod | VSW | 2024-01-08T16:38:25+00:00 | |
| Ender 3 Switchwire Y Tensioner Mod | Y Tension Mod | VSW | 2024-01-08T16:38:25+00:00 | |
| ByteChild | 2-Channel Relay DIN Rail Bracket | DIN Rail mounting bracket for an 2-Channel-Relay | V2.4 | 2024-01-08T16:38:25+00:00 |
| ESP32 DIN Rail Bracket | DIN rail mounting bracket for an ESP32 | V2.4 | 2024-01-08T16:38:25+00:00 | |
| bythorsthunder | MGN9 Backers Idlers | New idler uppers for MGN9 Extrusion backers | V2.4 | 2024-01-08T16:38:25+00:00 |
| Stealthburner Rapido UHF | Stealthburner mod for Rapido UHF | V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| CannedBass | PITFT50 45-degree mount | Mount that puts the screen at a 45-degree angle for more vertical... | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Trident Bed Fans | Bed fans for Trident | VT | 2024-01-08T16:38:25+00:00 | |
| Ch4rlesB | V0 Handles Slim | Simple and slim handles for the V0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| ChenTheDesignMaker | Z Belt Clip | Simple clip to keep extra Z belts clean and away from panels | V2.4 | 2024-01-08T16:38:25+00:00 |
| chirpy | V0.1 Nozzle Wiper | Servo powered nozzle wiper and purge bucket | V0.2 | 2024-01-08T16:38:25+00:00 |
| Runout UnKlicky Sensor | Runout UnKlicky Sensor is a filament runout sensor with mounts for... | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| V0.1 Raised Tophat | Alternative Tophat design that uses stock panels and raises height... | V0.2 | 2024-01-08T16:38:25+00:00 | |
| chri.kai.in | 20x20mm Profile Covers | Provide overlapping and flush slot covers for 20x20mm slot6... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Angry CAM USB | Housing for small USB camera module, allowing mounting to gantry or... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Exhaust Adapter 100mm | Replace 60mm exhaust fan with 100mm ventilation system adapter | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| chrisrgonzales | 270° Front Panel Hinge | Hinges that have 270° of swivel, parametric CAD included | V2.4 | 2024-01-08T16:38:25+00:00 |
| christophmueller | Phaetus and Zodiac Dragonfly BMO... | Covers both the original Phaetus variant as well as the Zodiac one. | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| claytono | Voron 2.4 Extrusion Jig | A jig help align extrusions to get a properly square frame | V2.4 | 2024-01-08T16:38:25+00:00 |
| Fysetc S6 V2 Mount | DIN Mount for the Fysetc S6 V2 controller | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 | |
| V0 Zip Tie Skirts | V0 skirts with small loops added along the top to allow zip tyiing... | V0.2 | 2024-01-08T16:38:25+00:00 | |
| clee | Monster8 DIN Rail Mounts | DIN mount for Makerbase Monster8 V1/V2 controller | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| cmrny | V0.1 Motor Panel Modification | V0.1 Motor panel modification to keep umbilical and bowden tube... | V0.2 | 2024-01-08T16:38:25+00:00 |
| conqueror433 | Voron Parts Logo | Voron Parts Logo for your back panels, 3D Print or Laser Cut | V2.4 | 2024-01-08T16:38:25+00:00 |
| Voron V0.1 Parts Logo | Voron Parts Logo for your V0 deck panel | V0.2 | 2024-01-08T16:38:25+00:00 | |
| consibonsi | Y-Mod SW 9mm | 9mm Y belt mod for SW | VSW | 2024-01-08T16:38:25+00:00 |
| csch0 | SW Fan Mount No Tape | 60x20 Fan Mount for SW without tape | VSW | 2024-01-08T16:38:25+00:00 |
| d3nny | Filtered Power Plug with... | Filtered Power Plug for RND 165-00057 and CAT6-Plug | V2.4 | 2024-01-08T16:38:25+00:00 |
| D4rkCelerity | Raspberry Pi Zero Bracket | Modified version of Trident RPi bracket to fit the smaller RPi Zero | V0.2, V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| DaGlo | V0.1 Duet 2 Wifi mounting brackets | Voron 0.1 Mounting brackets with/without RPi 4 | V0.2 | 2024-01-08T16:38:25+00:00 |
| Voron V0 Mean Well power supply... | Voron V0 Mean Well power supply bracket (Funssor Kit) | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Voron V0 SSR Mount | Voron V0 SSR Mount for the bottom | V0.2 | 2024-01-08T16:38:25+00:00 | |
| DaGrooch13 | Tophat Exhaust Filter V0 | Activated charcoal exhaust filter with HEPA that replaces the rear... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Dan88 | V0 one-part Skirts | One part Skirts for the V0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| dankeeling | Creative Live! Camera Mount | A mod to provide a mount for the Creative Live! Camera that mounts... | V2.4r2, VT | 2024-01-08T16:38:25+00:00 |
| DaStivi | The Cephalopod limb (BTT Octopus... | An alternative Din rail mount for BTT Octopus (PRO) boards | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Daten | Revo hotend skirt case | A skirt case for the Revo hotends to reside R1 and R2 | V2.4 | 2024-01-08T16:38:25+00:00 |
| davidauvergne | Center_cable_management_duct | Mod for a centered cable management | V2.4 | 2024-01-08T16:38:25+00:00 |
| DC67 | Plug Panel Mod for Schaffner... | A modified plug panel for the Power Entry Connector Schaffner... | V2.4 | 2024-01-08T16:38:25+00:00 |
| deepfriedheroin | v0 Wago Bed Mounts | Easy to install Wago mounts for the v0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| v0 Power Wagos | Easy to install Wago mounts for v0 mains | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V2 Bed Wagos | Wire management for the v2 bed | V2.4 | 2024-01-08T16:38:25+00:00 | |
| dePrintinator | HEPA Exhaust | HEPA filter chamber exhaust replacement. | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| DerekBackus | LED Strip Holder | Simple bracket to mount an LED strip | V2.4, VT | 2024-01-21T20:17:15+00:00 |
| Trident Right Skirt Switch | Moves power switch to right front skirt on the Trident | VT | 2024-01-21T20:17:15+00:00 | |
| Derpimus | V0.1 Block Handle | V0.1 Block Style Handle | V0.2 | 2024-01-08T16:38:25+00:00 |
| DorjeDorf | Duet 3 3HC Din Bracket | V2.4 Duet 3 3HC Din Bracket | V2.4 | 2024-01-08T16:38:25+00:00 |
| Duet 3 6HC Din Bracket | V2.4 Duet 3 6HC Din Bracket | V2.4 | 2024-01-08T16:38:25+00:00 | |
| doubletrouble | V0 Skirt Mod | V0 Skirt Mod | V0.2 | 2024-01-08T16:38:25+00:00 |
| Dr-Info | BTT 5160T Plus Mounts | Mounts for BTT 5160T Plus to DIN, 2020 and 1515 | V2.4, VT | 2024-02-01T10:07:10+00:00 |
| Corner Cable Cover with Drop Holes | Corner cable cover around Z-idler with drop holes near z frame and... | V2.4, VT | 2024-02-01T10:07:10+00:00 | |
| Lever Connector Mount Side Fan... | Mount Universal Lever Connectors or WAGO 221 using the side fan... | V2.4, VT | 2024-02-01T10:07:10+00:00 | |
| LRS DIN Mount Offset | Offset mount for LRS PSU on DIN rail with stabilizer | V2.4, VT | 2024-02-01T10:07:10+00:00 | |
| V2.4 Z Drive Motor Tensioner Mod | Braced motor tensioner for z drive | V2.4r2 | 2024-02-23T17:05:57+00:00 | |
| V2.4 Rear Skirt Mod for Z-Drive... | This mod enables the you to utilize the rear skirts, power and... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| DrGhetto | Ghetto Panels | Printed panels for the Voron Zero | V0.2 | 2024-01-08T16:38:25+00:00 |
| eamars | Stealthburner (RC1) Dragon... | The Stealthburner toolhead mount for Mellow Crazy, TriangleLab... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| eddie | LED Bar Clip | Modular LED Clip for mounting LED Strip to 2020 Extrusions | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| V1.8 12mm Z Mod | Add V1.8 option for 12mm Z rods | V1.8 | 2024-01-08T16:38:25+00:00 | |
| edwardyeeks | Tridentified V2.4 Power Inlet | Trident style side power inlet for V2.4 using Z Drive Motor... | V2.4 | 2024-01-08T16:38:25+00:00 |
| elcrni | Trident Internal Spool Holder | Internal spool holder for 300 and 350 Tridents. Supports full size... | VT | 2024-01-08T16:38:25+00:00 |
| V.24/Trident Spool Holder | Spool holder that mounts on top for "too close to the wall" printers | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Electroleon | U2C Mounting | Bigtreetech U2C CAN Interface mounting bracket | V0.2, V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Ellis | 15x15 Drag Chain End | 15x15 drag chain end piece | V2.4 | 2024-01-08T16:38:25+00:00 |
| Badge Retractor Mount | Extrusion mount for badge retractor to keep bowden tube out of the... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Bed Fans | Bed fan control macros and 5015 bed fan mounts | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Short Z Joints | Shorter Z joints for the v2.4 | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Single MGN9H Carriage | Single MGN9H toolhead carriage with toolhead x endstop support (for... | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 | |
| ElPoPo | Removable Doors | New hinge to easily remove the door and have a wide opening V2.x | V2.4 | 2024-01-08T16:38:25+00:00 |
| EmJay276 | Stealthburner Phaetus Dragon UHF... | This mod adds a tool cartridge for the Phaetus Dragon UHF and... | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Empusas | Mounts for BTT Filament Motion... | Mounts for Big Tree Tech Smart Filament Motion Sensor | V0.2, V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| Power Skirt 2.x FN284-10-06 | Power Skirt for Schaffner FN284-10-06 V2.x | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Mounts for Terminal Blocks NC933... | Mounts for Terminal Blocks NC933 and SPL-62 from AliExpress | V2.4 | 2024-01-08T16:38:25+00:00 | |
| evandepol | Crydom GN Terminal Guard | A simple safety guard for the terminals on a Crydom GN SSR | V2.4 | 2024-01-08T16:38:25+00:00 |
| Voron 2.4 cable clamps | A set of 2020-mounted cable guards to organize and dress the wiring... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| falo | LGX Lite CAN Side Mount | A side mounting for a CAN board (Huvud/SHT42) to the LGX Lite | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Magnetic Exhaust Grill Cover | A magnetic cover to seal the filtered exhaust | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Toolhead PCB to CAN Mount Adaptor | A mount to enable side mounting of a CAN board (Huvud/SHT42) in... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Ferdi360 | 2.4 Bedfan Backplates | Backplates for your Voron 2.4 that block hot air out of your... | V2.4r2 | 2024-01-08T16:38:25+00:00 |
| Fiction | C270 mount | Logitech C270 webcam front-centre mount | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Crossrail | Across-the-rails LRS-200-24 or RSP-200-24 mount using DRP-03 brackets | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Exhaust_cover | Cover for exhaust cutout in back panel | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Exhaust_cover_SFS | Exhaust cover and BTT Smart Filament Sensor mount | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| LGX Lite toolhead PCB mount | Mount for Hartk's toolhead PCB(s) for LGX Lite | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| filotto78 | 6mm slot cover | Simple cover for extrusion with 6mm slot width | V2.4 | 2024-01-08T16:38:25+00:00 |
| frankaf | Euclid Probe Carriage | A MGN-12 carriage with an inset mount for a Euclid Probe | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| FreeformFez | V1.8 Filtered Power Inlet | V1.6 Filtered Inlet and Rocker Switch for V1.8 | V1.8 | 2024-01-08T16:38:25+00:00 |
| GadgetAngel | Bed Support Extrusions Alignment... | The bed support alignment tools will assist in helping align the... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Cricut Voron Logos | For any cutting machines or machines that rely on vector graphics... | V0.2, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Galvanic | Bowden Tube Guide | Bowden tube guide and CANBUS wire support | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| gamebofh | Laser cut door panels | Files to allow you to create laser cut door panels with some... | VSW | 2024-01-08T16:38:25+00:00 |
| gauravmm | Crazy Mozzie HF toolhead SB+CW2 | Toolhead for Crazy Mozzie HF, compatible with Stealthburner and... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| gen2eng | Switchwire LED wire pass through | Z Carriage Stop modification that makes pass through of wires for... | VSW | 2024-01-08T16:38:25+00:00 |
| geoffreyyoung | Dual Rail Installation Guide | Rail installation guide that also works for the 2.4 dual rail... | V2.4 | 2024-01-08T16:38:25+00:00 |
| LGX Info, Links, and Models | Useful information and models for using the Bondtech LGX extruder... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| gerritwellen | Manta M8P Mount | Mounting Bracket for BTT Manta M8P | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| GiulianoM | Fly F407ZG Mount | Mount for the Fly F407ZG: https://github.com/FLYmaker/FLYF407ZG | V2.4 | 2024-01-08T16:38:25+00:00 |
| Gizzle | Ender 3 and Ender 3 Pro... | Mod for the Ender 3 and Ender 3 Pro, which adapts the kinematics... | VSW | 2024-01-08T16:38:25+00:00 |
| golas | V0.1 Extended tophat hinge | Extended tophat for v0.1 with hinges (integrated or screwed ones). | V0.2 | 2024-01-08T16:38:25+00:00 |
| V0.1 Trident skirt remix with... | Trident style v0.1 skirt mix with 12864 Mini Lcd on front or plain... | V0.2 | 2024-01-08T16:38:25+00:00 | |
| GSL12 | Pocketwatch Nema 17 | Extruder like Pocketwatch, but with Nema17 instead of Nema14. Maybe... | V0 | 2024-01-21T20:17:15+00:00 |
| hartk1213 | Voron0.2 2.8 Waveshare Display | 2.8 Waveshare display for V0.2 | V0.2 | 2025-05-29T01:45:55+00:00 |
| Voron0.2 Rear Keystone Skirt | Added keystone slot on rear skirt for V0.2 | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Voron0 C14Inlet | Added a new Power inlet that uses a Fused C14 plug and switch that... | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 deck panel | Used @Kruppes blank deck panel to add the logo as well as the name... | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 display dualcolor | Added a dual color file for the Voron Display Front housing | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 ExtendedLegs | New extended legs to raise the printer up a tiny bit more | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 ExtrusionSkirt | Created a new skirt design that uses 50mm extrusions as legs and it... | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 Hinged Top Hat | Created a new hinged top hat design for the V0 so it can fold away... | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron0 MGN9C X Axis | This mod, replaces the stock MGN7H for MGN9C on the V0 | V0.1 | 2024-01-08T16:38:25+00:00 | |
| Voron2.4 GE5C | This mod replaces the stack of printed z joints with a metal... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Voron2.4 SexBolt ZEndstop | This mod replaces stock V2 Z endstop with a different style | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Voron2.4 and Trident Pins Mod | This mod replaces all the M5 screws for all idlers/pulleys/bearings... | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Voron2.4 Y Endstop Relocation | This mod relocates the Y endstop to the top A drive piece | V2.4 | 2024-01-08T16:38:25+00:00 | |
| henrikssn | Parametric Spool Holder | Spool holder where the length is a parameter. | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Plug Panel Mod for Generic... | v2.4 plug panel for generic unfiltered modules with 66mm x 27mm... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| hergtoler | Exhaust Housing for 120mm Fan... | v2.4 Exhaust Housing for 120mm Fan and 4in Duct | V2.4 | 2024-01-08T16:38:25+00:00 |
| hernsl | Bottom Panel Mag Clip | v2.4 magnetic clips to retain bottom panel | V2.4 | 2024-01-08T16:38:25+00:00 |
| hhammarstrand | Afterburner connector cover for... | Connector cover for 42STH20-1004AS | VSW | 2024-01-08T16:38:25+00:00 |
| hijax_pl | Corner panel clip | V2 panel corner frames using 3-way L brackets in the corners | V2.4 | 2024-01-08T16:38:25+00:00 |
| Din Rail mount | Adapter to attach DIN Rail to 2020 extrusion. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Controler Board adapters | DIN (rotated) and legacy adapters for boards like SKR mini E3. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Hobson318 | Belt Tension Wrench | Wrench for easier turning of the belt tension knobs on V0.1 | V0.2 | 2024-01-08T16:38:25+00:00 |
| Klipper Expander Mount | Mounting brackets for the klipper expander using vhb tape or... | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| hoschi | FYSETC Spider DIN Rail Mount | DIN rail mount for FYSETC Spider | V2.4 | 2024-01-08T16:38:25+00:00 |
| hymness1 | 10x11mm chain VSW | Printable and openable 10x11mm chain | V0.2, VSW | 2024-01-08T16:38:25+00:00 |
| Quickdraw probe Voron Switchwire | Detachable magnetic probe with docking system for VSW | VSW | 2024-01-08T16:38:25+00:00 | |
| Iakabos | c920 Mount | Slim mount for logitech c920 webcam | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| V0 beltchains | Modified beltchain parts for V0 Z cables | V0.2 | 2024-01-08T16:38:25+00:00 | |
| iblue | V0.1 Tophat Extractor | Tophat Extractor for the Voron V0.1 with activated charcoal and... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Itzo1978 | PEI Stop | Stop for positioning your PEI | V2.4r2 | 2024-09-24T13:42:21+00:00 |
| jangrewe | Bitter USB Cam | Modification of the "Angry Cam USB v2.0" webcam mount for 1515... | V0 | 2024-01-08T16:38:25+00:00 |
| jappaj | V0.1 FanSaver | A printable fix for overheating V0.1 blower fans | V0.2 | 2024-01-08T16:38:25+00:00 |
| jasonc | V2.4 Z-Idler Shoulder Bolt Mod | Modification to the idler carriers to accept a 25mm shoulder bolt.... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Jasrags | Feed slot with filament pass-... | A feed slot with a filament pass-through | VSW | 2024-01-08T16:38:25+00:00 |
| jatson | Plug panel mod for Schurter... | A modified plug panel for Voron 2.4r1 with Schurter CD44.1101.151... | V2.4 | 2024-01-08T16:38:25+00:00 |
| jaysuk | 4.3 Fly Screen Mount | A mount for a 4.3" Fly Screen | V0, V0.1 | 2024-01-08T16:38:25+00:00 |
| JD | V2.4 Filament runout sensor | Replace the 2.4 stock bowden tube holder and add a filament runout... | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| jeoje | 4.3" Touchscreen Mount | Mounts a [Waveshare 4.3inch Capacitive Touch... | V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| Molex MLX and Microfit 3.0 Bed... | Solid mount your bed connectors | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Sturdy Handles | Modified v2.2 handles with no panel rest and with 4 anchor points | V2.4 | 2024-01-08T16:38:25+00:00 | |
| V2.4 Z Chain Guide with... | Modifies the Z chain guide to hold a chamber thermistor | V2.4 | 2024-01-08T16:38:25+00:00 | |
| JeremyRuhland | V2.4 Plug Panel Generic Combo | Skirt power panel for generic amazon plug/switch/fuse combo module,... | V2.4 | 2024-01-08T16:38:25+00:00 |
| jgehrig | V0 LCD Touchscreen Skirt | 3.2" LCD Touch Screen Skirt | V0.2 | 2024-01-08T16:38:25+00:00 |
| JJFX | V2.4 CR Touch Snap Mount | Mount to replace v2.4 (MGN9) probe with a Creality CR Touch | V2.4 | 2024-01-08T16:38:25+00:00 |
| JNP | Back Door | Door for easy hardware access | V0.2 | 2024-01-08T16:38:25+00:00 |
| Deck Panel | Covers the hotbed cables | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Drawer | Drawer in four different versions | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Front Door | Door in a frame | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Hepa Filter | Filter case with fan´s | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Mid Panel | Panel for SKR1.4/1.4 or SKR E3 mini mount | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Neopixel Case | mounting for Neopixel strip with 8 LED´s | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Side Panels | Panels with intergrated hinge | V0.2 | 2024-01-08T16:38:25+00:00 | |
| johanncc | Raspberry Pi Camera Mount | Low profile raspberry pi camera mount | V0.2 | 2024-01-08T16:38:25+00:00 |
| Jon | 1515 LED Mount | Snap in 1515 Led mount for WS2812B | V0.2 | 2024-01-08T16:38:25+00:00 |
| adxl345 skirt keystone | Skirt keystone for ADXL345 using Microfit 3.0 | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Z Cover for v0.1 | A cover to stop things from dropping down the Z motor and... | V0.1 | 2024-01-08T16:38:25+00:00 | |
| joposter | V0 Clippable LED Caselight | LED Case light for the V0 that clips into the extrusions | V0.2 | 2024-01-08T16:38:25+00:00 |
| JosAr | Klicky Probe | Microswitch based inductive probe replacement | V0.2, V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| KenadyDwag44 | Switchwire Lightbar | A LED lightbar for switchwire | VSW | 2024-01-08T16:38:25+00:00 |
| KevinAkaSam | VEFACH | Voron Exhaust Filter Inserts for Activated Coal + Hepa | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| khay | V0 Micro Backplate | Minimalistic backplate for cooler motors and electronics | V0.2 | 2024-03-14T16:46:20+00:00 |
| Fan for V2-200mm² | Middle Skirt for V2-200mm² Electronics Compartment | V2.4 | 2024-03-14T16:46:20+00:00 | |
| 3x Keystone PlugPanel | PlugPanel with Options for 3 Keystones | V2.4 | 2024-03-14T16:46:20+00:00 | |
| KiloQubit | Trident Schurter Inlet Skirt | Trident inlet skirt for mounting a Schurter DD11.0124 or similar inlet | VT | 2024-01-08T16:38:25+00:00 |
| V0 Reverse Bowden Mount | V0 reverse bowden mount | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V2.4 Z Chain Mounts for 3 Hole... | Z chain mounts for 3 hole generic chain | V2.4 | 2024-01-08T16:38:25+00:00 | |
| kirby | V0 Sherpa Mini Direct Drive Mod | A direct drive mod for the V0 using the Annex Sherpa Mini extruder | V0.2 | 2024-01-08T16:38:25+00:00 |
| Koios | 6mm Tempered Glass Mod | Lock levers and rests for 6mm Tempered glass panels | V2.4 | 2024-01-08T16:38:25+00:00 |
| C920 Low Profile Mount | Low profile mount for a C920 Webcam | V2.4 | 2024-01-08T16:38:25+00:00 | |
| LED Bar Mounts | Low profile mount for led bar lights | V2.4 | 2024-01-08T16:38:25+00:00 | |
| V0 C920 Tophat Mount | Mounting bracket for a Logitech C920 on the tophat | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Kosh42EFG | Kirigami bed front | Printed bed front for kirigami folded metal bed mount with Voron logo. | V0.2 | 2024-01-08T16:38:25+00:00 |
| Kruppes | Encosed Bottom | Modified printed parts and panel to fully enclose V0. | V0.2 | 2024-01-08T16:38:25+00:00 |
| V0 Printed Deck with inserts | Electronics Deck Panel using brass heat inserts. Optional with... | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Belt Tension Meter | Print in place tension meter to easily tighten multiple belts to... | V0.2, V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 | |
| Kyleisah | CableGator Cable Comb | A cable comb for simplifying and tidying wire harnesses for... | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| lakai | Bruag Skirts | V2 350mm skirts inspired by Bruag Facades | V2.4 | 2024-01-08T16:38:25+00:00 |
| Le0n | Magnetic panels with Magnet Inserts | Magnetic panel mounts with magnets inserted into frame slots. | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| leandromarceddu | PowerSkirt | Modified skirtpiece for a digital power monitor | V2.4 | 2024-01-08T16:38:25+00:00 |
| Liselotte111 | Red Lizard K1 UHF toolhead | SB toolhead for Red Lizard K1 UHF | V2, VT | 2024-01-08T16:38:25+00:00 |
| littleferris | V0 c14 Skirt Inlet | V0 C14 Skirt inlet | V0.2 | 2024-01-08T16:38:25+00:00 |
| LJ | Scrubby | Easy to use filament dust filter | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| LoCoCNC | 3mm Top Hat Panels Clips | Required to use the 3mm (1/8") thick top hat panels for V0.1 | V0.2 | 2024-01-08T16:38:25+00:00 |
| MGN7H Shims | Shims for making bearing cartridges coplanar | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Mosquito PTFE 15mm Tube Cutting Jig | Tool to precicely cut 15mm PTFE Tube | V0.2 | 2024-01-08T16:38:25+00:00 | |
| SSR Mounting Strap | Mounting Strap for SSR on 1515 Extrusions | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Strain Relief w/ 10 Pin Microfit | Strain Relief with 10 pin Microfit connector | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V2.4 Bed Wiring Grommet | Safely capture your bed wires thru the bottom panel | V2.4 | 2024-01-08T16:38:25+00:00 | |
| LoganFraser | ComboInlet | Skirt pieces for Trident, 2.4 and 2.4r2 for combo inlets in 2 sizes. | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| HorseshoeSpoolHolder | Horseshoe Spool Holder - mounts internally for Trident, or... | V0.2, V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| PiPlate | PiPlate - Raspberry Pi3,4 mounting plate and Skirt Mod for... | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Trident Inverted Electronics | Flip the Trident electronics bay for top access. | VT | 2024-01-08T16:38:25+00:00 | |
| WagoMounts | Wago Mounts for Din Rail or 2020 Extrusion mounting. | V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Long | Mantis Dual 5015 Toolhead | MGN12 Dual 5015 Toolhead for 2.4 & 1.8 | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| Lukas | SSD1306 Case Front Cover | SSD1306 Mount replacement for Mini12864 | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Mac10goesBRRRT | PiTFT Mount | Mount for the BTT PiTFT Touchscreen | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| madfabrications | Vertical PSU Mount | Mounts the PSU vertically on the DIN rails | V2.4 | 2024-01-08T16:38:25+00:00 |
| madros | V0 OLED-skirt | V0 skirt with 0.96" OLED | V0.2 | 2024-01-08T16:38:25+00:00 |
| Majarspeed | Hartk board mount galileo | It hangs stuff on your tool | V2.4 | 2024-01-08T16:38:25+00:00 |
| MakeALeft | Switchwire Clean Center Grill | Removed magnet holders on center panel for cleaner look | VSW | 2024-01-21T20:17:15+00:00 |
| MapleLeafMakers | Kirigami Stealth Bumper | an RGB-Powered front-bed mount for the Voron V0 with Kirigami Bed... | V0 | 2024-01-08T16:38:25+00:00 |
| Matchstick Diffusers | Mounts and Diffusers for the popular "on-a-matchstick" LEDs | V0 | 2024-01-08T16:38:25+00:00 | |
| Modesty Mesh | Customizable mesh inserts to hide your messy electronics compartment. | V0 | 2024-01-08T16:38:25+00:00 | |
| Rainbow Serial Bumper | Just a little bit of extra bling for your Voron Trident | VT | 2024-01-08T16:38:25+00:00 | |
| Stealth Handles | Stealthy and stylish handles for your V0 | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Umbilical Collar | An adjustable umbilical collar for the stock motor panel on the V0 | V0 | 2024-01-08T16:38:25+00:00 | |
| Upper Rear Bowden Inlet (URBI) | A Reverse Bowden Inlet for the upper-rear panel of the Voron Zero... | V0 | 2024-01-08T16:38:25+00:00 | |
| MasturMynd | Stealth Zero | A low poly gantry with front tensioners and optional front mounted... | V0.1 | 2024-01-08T16:38:25+00:00 |
| 2-Piece Z Tensioners | Splits the tensioners into two pieces, allowing the tensioner to be... | V2 | 2024-01-08T16:38:25+00:00 | |
| MathematicalPotato | V0.1 Belted Z Drive | Conversion to a belted Z axis for the V0.1 adapted from... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Maverick | MiniSB_LGXL | A Bondtech LGX Lite variant of the MiniSB | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| MiniSB_Rapido | Modified MiniSB to use a Rapido hotend | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| MiniSB_Sharkfin | Modified MiniSB to use a Sharkfin Extruder | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| V0.2 Stealth Skirts | Juiced up skirts for the V0.2 | V0.2 | 2024-01-08T16:38:25+00:00 | |
| maximilian-foerg | Afterburner Turbo Mod | A purely cosmetic mod for Afterburner | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Switchwire Double 60mm Fan Mount | A mount for two (or four) 60mm fans in SW's electronics compartment | VSW | 2024-01-08T16:38:25+00:00 | |
| Mckurt | Switchwire Y Belt Tensioner | Switchwie Y axis Belt Tensioner | VSW | 2024-01-08T16:38:25+00:00 |
| MCMBen | Voron0 Block & Tackle Z Belt | A block & tackle belted Z solution using NEMA14. Ratios from 5:1 to... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Mellow | V0 Fly-Gemini | Fly-Gemini adapted model for V0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| mikepthomas | MKS Mosfet Mount | MKS Mosfet Mount based of the Trident Raspberry Pi Mount. | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| MikesMods | LGX mount for V0.1 with 2nd X rail | V0.1 mod for mounting Bondtech LGX extruder with addition of 2nd X... | V0.2 | 2024-01-08T16:38:25+00:00 |
| Minsekt | Rear Umbilical | Rear Umbilical mounting solution including a relocated Y-Endstop | V2.4 | 2024-01-08T16:38:25+00:00 |
| mjoaris | 10x11 Cable Chain Endcaps | Printable Endcaps for 10x11 Cable Chains | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| Mini12864 LCD Mount | Swiveling case for the Fysetc Mini12864 LCD | V2.4 | 2024-01-08T16:38:25+00:00 | |
| mosher | Door hinges with M3 screws shafts | Simple mod of print in place door hinges, which uses m3 screws as... | V2.4 | 2024-01-08T16:38:25+00:00 |
| mpfl | V0.1 OLED-skirt | V0.1 skirt with 0.96" OLED | V0.2 | 2024-01-08T16:38:25+00:00 |
| MrBean66 | SKR Pro DIN Mount | Simple mod to mount the SKR Pro board from BTT to a DIN rails. | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| MrDespair | MiniAB Pinda Probe Mount | Replacement MiniAB Cowling to add a mount for a Pinda style probe. | V0.2 | 2024-01-08T16:38:25+00:00 |
| Mrgl-Mrgl | LGX Lite Mount | a mount for the LGX Lite | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| MSA | Belt tension helper | Belt tension helper for V0.1 | V0.2 | 2024-01-08T16:38:25+00:00 |
| MSiemons | Tophat Hinge V0 | Simple hinge for V0 Tophat | V0.2 | 2024-01-08T16:38:25+00:00 |
| muradir | Zodiac BMO Stealthburner Toolhead | A Stealthburner toolhead for the Zodiac BMO Hotend, based on the... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Nashuar | V0 Dragon Toolhead M2.5x8 | This toolhead uses the stock M2.5 screw that came with the dragon... | V0.2 | 2024-01-08T16:38:25+00:00 |
| natewalck | V1.8 Jigs | Jigs for assembling V1.8 | V1.8 | 2024-01-08T16:38:25+00:00 |
| nhchiu | V0.1 Movable Pulley Z Drive | A movable pulley system on the Z axis with 1:8 total speed ratio... | V0.1 | 2024-01-08T16:38:25+00:00 |
| nikolasbabetas | Neopixel Holder | A holder to attach Neopixel/WS2812B Led Strips to the V0.1 | V0.1 | 2024-01-08T16:38:25+00:00 |
| Nomsplease | 60mm Shaft Jig | Simple jig for cutting and grinding 60mm Z shafts | V2.4 | 2024-01-08T16:38:25+00:00 |
| Duet Wifi Mount | Duet wifi mount in pocketwatch location | V0.2 | 2024-01-08T16:38:25+00:00 | |
| LED Mounts | Basic LED mounts for 10 and 12mm strips | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Remixed Panel Mounts | Remixed rear bottom panel mounts with stop | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Pi Cam/ZeroW Mount | Mount for pi camera and ZeroW | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Pocket Watch Rear Reolcation... | Pocket watch rear reolcation bracket | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Oakman | BTT 24V UPS Metal DIN Mount | Adapter to use a metal DIN mount for the BTT 24V UPS | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| FYSETC Spider Metal DIN Mount | Use a metal DIN mount for your FYSETC Spider | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 | |
| RPI Metal DIN Mount | Adapter for metal DIN mounting the Raspberry Pi | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 | |
| OboMaker3D | C17-EXT Filter HEPA Carbon | Replaces standard filter with new HEPA Crabon and 120mm fan V1.1 | V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| C17-EXT-CARTRIDGE for C17-EXT... | Alternative to a commercial cartridge for the C17-EXT filter | V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| ommy | roller brackets | Brackets to help rolling V2 on its side. | V2.4 | 2024-01-08T16:38:25+00:00 |
| oxno | RBP Zero Bracket | Bracket for Raspberry pi zero. | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| padok | Chain Anchor - ADXL345 mount Mod | A ADXL345 mount for the Afterburner | V2.4 | 2024-01-08T16:38:25+00:00 |
| Phalanx | "Other" Idlers Mod | Allow usage of wider toolheads on the V2 | V2.4 | 2024-01-08T16:38:25+00:00 |
| piet206 | V1.8 Z Rails Mod | Add MGN12H linear rails for Z axis motion | V1.8 | 2024-01-08T16:38:25+00:00 |
| Polar-Ted | V0.1 Z nozzle endstop switch | Sexbolt style switch for V0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| V0.1 Two Piece Back Panel | Vented 2 piece back panel for V0 | V0.2 | 2024-01-08T16:38:25+00:00 | |
| Polared | Power Inlet with Keystone Insert | Voron 0.1 Power inlet with keystone insert slot | V0.2 | 2024-01-08T16:38:25+00:00 |
| ponkotsu1 | V0 Launchpad Skirt | Another style V0 skirt | V0 | 2024-01-08T16:38:25+00:00 |
| ppak10 | Cable Port Flush Mount Skirt | Provides an inlet to mount BATIGE circular cable adapter ports on... | V2.4r2 | 2024-01-25T17:26:27+00:00 |
| Enclosed Z-Chain Guide | Supports Z-Chain from both sides and keeps it from sliding around,... | V2.4r2 | 2024-05-08T21:51:38+00:00 | |
| prasadp4009 | StealthBurner CR Touch Mod | Voron SW StealthBurner CR Touch Mod | VSW | 2024-01-08T16:38:25+00:00 |
| Printopal | Magnetic top panel | Top panel with magnets allows for quick installation and removal | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| PsychoShaft | C92X_PsycHoShafts_Mount | 2020 Top profile 920 camera mount / 2 point axis pivot | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| QuackProfit | V0 Adafruit NeoPixel LED Mounts | Mount Adafruit PCB NeoPixel Sticks on the V0 Y-rail extrusions | V0.2 | 2024-01-08T16:38:25+00:00 |
| quattroerik | V2.4 Door Hinge M3 3mm 180deg | Voron 2.4 door hinges for 3mm panel, 180 deg opening and m3 screw... | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| randell | Door Hinges | Door hinges that use an M3 bolt for a pin and bolts thru the panel | V2.4 | 2024-01-08T16:38:25+00:00 |
| Microswitch Pod for PCB | Modified endstop pod for use of endstop switches mounted on a PCB | V2.4 | 2024-01-08T16:38:25+00:00 | |
| raymondh | Large Spool Holders | Larger spool holders for KVP spools | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| reapola | MKS CANable Pro DIN Mount | MKS CANable Pro mount which mounts on a DIN rail | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Reemuson | CYD Screen Case | A VORON Switchwire mount-able case for the CYD screen. | VSW | 2024-03-31T00:45:03+00:00 |
| reQu1em00 | Kirigami LED Bed Front | Kirigami bed front with space for a single LED or Neopixel button | V0.2 | 2024-01-08T16:38:25+00:00 |
| revnull | Raspberry Pi 7inch Display Mount | An articulating mount for the offical Raspberry Pi 7inch touch screen | V2.4 | 2024-01-08T16:38:25+00:00 |
| Rhastlyn | 60mm Fan Cover | A easy to install cover for spec 60mm fans originally designed for... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Wansview 1080p Camera Mount | A camera mount that replaces the OEM part to allow the camera to be... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| richardjm | ADXL drag chain mount | Permanent mount for ADXL boards on the back of the motor, replacing... | V2.4 | 2024-01-08T16:38:25+00:00 |
| Back blanking plate | Back blanking plate that can be used instead of the exhaust filter... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| LED 15.5mm quarter round mounts | Mounting corners with integrated cable runs for 15.5mm quarter... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Picam corner mount | Out of the way corner mounted picam | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Printable snap latches for 2020... | Quick release panel latch inspired by the work of others. | V2.4 | 2024-01-08T16:38:25+00:00 | |
| RikersBeard | RS-50-5 PSU Bracket | A Meanwell RS-50-5 PSU DIN rail mount bracket. | V2.4r2, VT | 2024-07-04T20:34:19+00:00 |
| rngSplat | Printable Switchwire Deck Plate | Print a deck plate for Switchwire with debossed Voron logo | VSW | 2024-01-08T16:38:25+00:00 |
| roboticator24 | Touchscreen for OctoDash | Mount a 4-inch LCD touchscreen to your V2.4 in place of the usual... | V2.4 | 2024-01-08T16:38:25+00:00 |
| RockNLol | RockNRoll | Rockers to roll the printer on its back for easier access to the... | V2.4 | 2024-01-08T16:38:25+00:00 |
| rsheng118 | BTT octopus DIN vertical mount | DIN vertical mount for Big Tech Tree Octopus board | V2.4 | 2024-01-08T16:38:25+00:00 |
| ruiqimao | V0.2 MGN9C X Axis | MGN9C linear rail for the X axis on V0.2 | V0 | 2024-01-08T16:38:25+00:00 |
| ryandam | Cable Management Duct | Zip tie mount intergrated cable duct to hide your cable | V0.2 | 2024-01-08T16:38:25+00:00 |
| sammynorway | LGX stealthburner connector cover | Cable cover for LGX and stealthburner | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| samwiseg0 | 4 Channel Relay Under Deck Mount | Mod to mount a 4 channel GPIO controlled relay | V2.4 | 2024-01-08T16:38:25+00:00 |
| AB Plug (Microfit 1x4) | Mod to mount A & B motor connectors to the gantry | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Corner Cable Hide/Cover (LED Wires) | Mod to hide cables around z idlers | V2.4 | 2024-01-08T16:38:25+00:00 | |
| ESP8266 NodeMCU Din Mount | Din mount for ESP8266 NodeMCU | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| Extrusion/Chamber Thermistor Mount | Extrusion mount for a NTC100K Thermistor extrusion | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| LRS PSU Screw Terminal Cover | Mod to cover the screw terminals for several LRS style PSUs | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Microfit 2x3 Skirt Connector (ADXL) | Mod for a Microfit 2x3 connector to be mounted in a skirt | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Corsair Flash Voyager GTX Din Mount | Din carrier for a Corsair Flash Voyager GTX | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| scanlory | Clip-On Front Door Frame | Clip-on frame to stiffen and seal front door panels when using... | V2.4 | 2024-01-08T16:38:25+00:00 |
| ScramblerUSA | Side Skirt Power Switch | Skirt-mounted rocker switch for easy access for Voron 2.4 | V2.4 | 2024-01-08T16:38:25+00:00 |
| See1807 | TopHat Exhaust and LED Light | A mount for 10mm LED strips and Exhaust for Voron V0 | V0.2 | 2024-01-08T16:38:25+00:00 |
| sgr33n | 300mm X-Extrusion Endcap | This mod makes stabler and prettier the use of a 300mm profile for... | VSW | 2024-05-26T21:49:13+00:00 |
| Shiftingtech | Trident Dual Power Switch | A replacement skirt, allowing 2 power switches | VT | 2024-01-08T16:38:25+00:00 |
| ShinyPants | OrangePi 3 LTS DIN Rail bracket | A DIN rail mount for OrangePi LTS 3 | V1.8, V2.4, VT | 2024-01-08T16:38:25+00:00 |
| Shteeeeeve | V0.1 LED Tophat | V0.1 LED Tophat w/ 24V LED Lightstrip | V0.2 | 2024-01-08T16:38:25+00:00 |
| Sjack1209 | Voron Fridge Door Light Switch | This mod allows you to maintain software control of your white LED... | V2.4r2, VT | 2025-12-30T22:22:09+00:00 |
| Slidr | PanzerBalls 2.4 | Squash Ball Feet for V2.4 | V2.4 | 2024-01-08T16:38:25+00:00 |
| PanzerChain 2.4 | Energychain for V2.4 | V2.4 | 2024-01-08T16:38:25+00:00 | |
| slitte | PCB_Probe | PCB for BAT85 and pull up resistor | V2.4, VT | 2024-01-08T16:38:25+00:00 |
| ssd_bracket | bracket for mounting a 2.5" ssd to a din rail | V2.4, VT | 2024-01-08T16:38:25+00:00 | |
| sloscotty | Switchwire Wall Plate | SW plate for enclosure | VSW | 2024-01-08T16:38:25+00:00 |
| NoNutz TopHat Cam Extension | Tophat extension with integrated webcam for V0/0.1 | V0.2 | 2024-01-08T16:38:25+00:00 | |
| spacelab2021 | Orbiter Clockwork Mount | A clockwork adaptor for the Orbiter v1.5 Extruder with full... | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| Spaghetti-Bolognese | LCD Case Mod | Improvements to the V2.4 mini12864 LCD case inc E-stop button cover | V2.4 | 2024-01-08T16:38:25+00:00 |
| Simplified Z Drive Motor Mount | Z drive motor mount bracket mod to improve pulley to belt alignment | V2.4 | 2024-01-08T16:38:25+00:00 | |
| sse018 | Octopus DIN Rail bracket | A Din rail mount for BTT Octopus board | V2.4 | 2024-01-08T16:38:25+00:00 |
| strayr | Creality toolhead for stealthburner | Use a creality ender 3 style hotend with stealthburner | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| sttts | Waveshare 5.5inch HDMI AMOLED Mount | Mod to mount a Waveshare 5.5inch full HD display on a V2 | V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| StvPtrsn | Skirts for a 320mm Build | Skirts for a 320mm build | V2.4 | 2024-01-08T16:38:25+00:00 |
| Keystone Jack for Filtered Mains... | Add a keystone jack to your filtered mains plug panel | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Parts_Jigs and Mods | Parts, Jigs and modifications I use for my builds | V0.2, V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 | |
| Side Fan Support, No Tape | Mount the 60mm side fans and inserts without tape | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Takuya | WANSVIEW USB Camera Mount | WANSVIEW 1080p Camera Mount for Voron 2.4 | V2.4 | 2024-01-08T16:38:25+00:00 |
| tallman5 | Z Locks | Helping hands curing v2.4 build, replaces long zip ties. | V2.4 | 2024-01-08T16:38:25+00:00 |
| tameike | Din Rail 2020 Holder | Attaching DIN Rails to 2020 | V2.4 | 2024-01-08T16:38:25+00:00 |
| Din Rail SKR 90 deg | SKR V1.3 bracket turned 90 degrees | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Jetpack V0 base | Attach Jetpack to V0 frame | V0.2 | 2024-01-08T16:38:25+00:00 | |
| TacoRaven Mounting Frame | TR V0 mount | V0.2 | 2024-01-08T16:38:25+00:00 | |
| tayto-chip | V2.4 Skirt Switch Mod | Add a ON/OFF Switch to side or front skirts | V2.4 | 2024-01-08T16:38:25+00:00 |
| techprolet | 2020 Aplic Cam Mount | Aplic HD camera to the 2020 frame at bed level. | V2.4r2 | 2024-03-14T16:27:05+00:00 |
| teookie | AB dial indicator mount | Mount for attaching standard dial indicators to AB | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 |
| SKR Brace | Rigidize and stabilize SKR 1.4 mounts | V2.4 | 2024-01-08T16:38:25+00:00 | |
| th0mpy | BEEFY Din Clips | Two piece BEEFY Din Clips, holds stronger | V2.4 | 2024-01-08T16:38:25+00:00 |
| TheSquiffy | V0 Belts holder | V0 Belts Holder | V0.2 | 2024-01-08T16:38:25+00:00 |
| TiagoBarata | Logitech C270 Mount | Logitech C270 Top Center Mount | V2.4 | 2024-01-08T16:38:25+00:00 |
| Tircown | DIN mount RS-15-5 PSU | A DIN mount for the RS-15-5 | V2.4 | 2024-01-08T16:38:25+00:00 |
| Display mount 5" | Tiltable mount for a 5" tactile display | V2.4 | 2024-01-08T16:38:25+00:00 | |
| Raspberry in plug panel | Raspberry mount vertically in the plug panel, allow easy access to... | V2.4 | 2024-01-08T16:38:25+00:00 | |
| V0.1 Skirt buttons | Buttons for V0.1 spec skirts | V0.2 | 2024-01-08T16:38:25+00:00 | |
| togi | Exhaust housing side fitting | Moves the exhaust housing bowden fitting 90 degrees to allow the... | V2.4 | 2024-01-08T16:38:25+00:00 |
| top_gun_de | mount_for_umbilical | Umbilical guide that goes on the chain anchor | V2.4 | 2024-01-08T16:38:25+00:00 |
| Triano | Ender 3 Pro or V2 to Switchwire Mod | Convesion of an Ender 3 Pro or V2 to a Switchwire | VSW | 2024-01-08T16:38:25+00:00 |
| Ultrawaffles | Ender 3 to SW conversion | A conversion mod for the ender 3 to switchwire. Designed to allow... | VSW | 2024-01-08T16:38:25+00:00 |
| VinnyCordeiro | RGB LED grid for Stealthburner | A small RGB LED grid for Stealthburner's logo | V1.8, V2.4, VSW, VT | 2024-01-08T16:38:25+00:00 |
| warriorofwire | Slenderfan for Afterburner | Lighter, quieter, smaller Afterburner | V2.4 | 2024-01-08T16:38:25+00:00 |
| watt-this | In Situ Linear Carriage Block... | A modification that allow lubrication of the linear reals while... | V2.4r2 | 2024-01-08T16:38:25+00:00 |
| Weaslus | Electronics Bay and Enclosure... | Better enclose chamber and keep heat from electronics | V0.2 | 2024-01-08T16:38:25+00:00 |
| whoppingpochard | Extrusion Backers | Laser-cut metal pieces to counteract bimetallic frame warping | V2.4 | 2024-01-08T16:38:25+00:00 |
| wile-e1 | Deck Panel Support Clips | Clips to help support lower deck panels to prevent (or fix) warping: | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 |
| Stealthburner + CW1 + PCB Cover | Low-poly for Stealthburner + CW1 + PCB installations: | V1.8, V2.4, VSW | 2024-01-08T16:38:25+00:00 | |
| wrez | V0 Alternate IEC 320 C14 Power... | Drop in replacement for alternate-source power inlet if spec inlet... | V0.2 | 2024-01-08T16:38:25+00:00 |
| xbst_ | ADXL345 V0 Mount | V0 Mount for a ADXL345 module | V0.2 | 2024-03-14T14:43:28+00:00 |
| Car Hood Style Bed Hinge | A way of reaching electronics from the top by having a "car hood"... | V2.4 | 2024-03-14T14:43:28+00:00 | |
| Duct Mount | 100mm/4" ducting mount for ventilation. Also supports umbilical... | V2.4 | 2024-03-14T14:43:28+00:00 | |
| DuetZero | Pi Zero mount over a Duet2 for space saving | V0.2, V1.8, V2.4 | 2024-03-14T14:43:28+00:00 | |
| Easy Access Rear Panels | New rear panels designed to expose the extruder for easy filament... | V0.2 | 2024-03-14T14:43:28+00:00 | |
| Flat V2.4 Skirts | Flat V2.4 Skirts so a panel without cutouts can be used | V2.4 | 2024-03-14T14:43:28+00:00 | |
| Hat LED Mount | Top Hat LED module mount | V0.2 | 2024-01-08T16:38:25+00:00 | |
| HOYMK SSR Mount | Mount for Chinese HOYMK SSR | V0.2 | 2024-03-14T14:43:28+00:00 | |
| PCB LED Holder | Very simple mount for some (?) PCB LED Bars | V1.8, V2.4 | 2024-01-08T16:38:25+00:00 | |
| DIN Mount Max31865 | A simple DIN rail mount for the Adafruit (or SAME SIZE clone)... | V1.8, V2.4 | 2024-03-14T14:43:28+00:00 | |
| DIN Mount Omron Relay | A simple DIN rail mount for the BOM Relay | V1.8, V2.4 | 2024-03-14T14:43:28+00:00 | |
| DIN Mount Pi 4x Relay Board | A simple DIN rail mount for the 4 channel relay board for Raspberry Pi | V1.8, V2.4 | 2024-03-14T14:43:28+00:00 | |
| V0 Electronics Cover | A printed cover for v0 electronics. Requires larger printer to print. | V0.2 | 2024-03-14T14:43:28+00:00 | |
| Mobius 4 (M4) V0 Mod | Mod to mount a M4 extruder to a Voron 0 where pocketwatch extruder... | V0.2 | 2024-03-14T14:43:28+00:00 | |
| V0 PiCam Mount | A Raspberry Pi Camera Mount For V0 | V0.2 | 2024-03-14T14:43:28+00:00 | |
| Screwed Front Door Hinge | Mod to screw the front door panel (instead of VHB) | V0.2 | 2024-03-14T14:43:28+00:00 | |
| V0 Buttons & OLED Mount | Mod to mount custom Gcode macro buttons & Waveshare 1.3" OLED display | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V2.4 Fanless Middle Skirt | A Fanless alternative middle side skirt | V2.4 | 2024-03-14T14:43:28+00:00 | |
| V2.4 Skirt Buttons | Skirt mod for custom Gcode macro buttons | V2.4 | 2024-01-08T16:38:25+00:00 | |
| ZipClip V0 | Very simple ziptie mount for v0 1515 extrusions | V0.2 | 2024-03-14T14:43:28+00:00 | |
| xceled | Single Panel Magnet Mount | Mount your front panel using only magnets | V2.4 | 2024-01-08T16:38:25+00:00 |
| yenda | SW More Robust XZ Belt Paths | Small mods to belt routing components to ensure a better/more... | VSW | 2024-01-08T16:38:25+00:00 |
| yeri | V0 Magnetic Panels | Mount V0 panels with magnets, removes need for hinges and lets you... | V0.2 | 2024-01-08T16:38:25+00:00 |
| V1 3Z | 3Z mod for V1 | V1.8 | 2024-01-08T16:38:25+00:00 | |
| Zen3D | V0 1515 T-nut | M3 square and hex nuts for Voron0 1515 frame | V0.2 | 2024-01-08T16:38:25+00:00 |
| V0 Handle | Voron0 Handle for 3mm panels | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V0 MidPanel HexPattern | Voron0 MidPanel with Hex pattern and Wire cover | V0.2 | 2024-01-08T16:38:25+00:00 | |
| V0 Skirt set | SSR, PowerSwitch, Adxl, Nameplate and color change printing | V0.2 | 2024-01-08T16:38:25+00:00 | |
| zruncho | V0 No-Drop Nuts | Voron0 nut inserts which auto-align (LDO frames only) | V0.2 | 2024-01-08T16:38:25+00:00 |
| ZZP8202 | Double_GEAR_ratio_Z | Double_GEAR_ratio_Z_belt_assembly_with_spherical_bearing_connection | V2.4 | 2024-07-14T14:53:20+00:00 |
| Pull-out electrical store | Voron 2.4 Pull-out electrical store（350mm only） | V2.4 | 2024-01-08T16:38:25+00:00 |
printer_mods
Directory actions
More options
Directory actions
More options
printer_mods
Folders and files
| Name | Name | Last commit date | ||
|---|---|---|---|---|
parent directory.. | ||||