Skip to content

README_HW2.x.md

Latest commit

 

History

History
99 lines (78 loc) · 4.38 KB

README_HW2.x.md

File metadata and controls

99 lines (78 loc) · 4.38 KB

DDS-AD9959-Arduino-Shield

4-Channels DDS (Direct Digital Synthesis) Analog Devices AD9959 Arduino Shield by GRA & AFCH

Web-site: https://gra-afch.com Direct link to category: https://gra-afch.com/product-category/rf-units/

What's New in Version 2.х

  • The display on the SH1106 controller has been replaced with SSD1306/SSD1309.
  • A software-controlled clock source switch has been added.
  • A LED indicators of active REF CLK IN.

GA Flasher or xLoader can be used to upload compiled firmware from "Firmware Compiled (.HEX File)" folder:

GA Flasher

"Firmware Compiled (.HEX File)" - folder contains pre-Compiled firmware (.HEX File), that can be uploaded via "AvrDude", GA_Flasher or any other software for flashing Atmega 2560

"Firmware Source (.INO File)" - folder contains source of firmware that can be compiled (modified if necessary) and uploaded via Arduino IDE: https://www.arduino.cc/en/Main/Software

"Libraries" - contains libraries that are only needed for compilation: place them to "C:\Users[USER]\Documents\Arduino\libraries", where [USER] - your windows username.

This AD9959 Shield can be easily connected to Arduino Mega without additional wires and converters. All functions of the DDS AD9959 are brought to the contacts of the Arduino Mega thanks to this you can fully reveal all the capabilities of the DDS AD9959.

Key Benefits:

  • Low harmonics no more than -60dB. An output RF transformer is used for the correct operation of the current mirror.

  • balancing transformer for TCXO and REF CLK IN options

  • Small spur

  • 4 layer board. Signal lines TOP and Bottom, inner layers Ground and Power.

  • Low Noise LDO Stabilizers

  • Separate power supply for all analog and digital lines (1.8 and 3.3V), 5pcs IC voltage stabilizers are used. Additionally, there is an RF Ferrite bead interchange.

  • High-speed decoupling Level converter and TTL 5V matching

  • one of these types of clock source can be used/installed:

    1. Onboard TCXO/OCXO - 5 - 50 MHz 1ppm (PLL),
    2. External TCXO/OCXO - 5 - 50 MHz (PLL)
    3. REF CLK IN - external generator 400 MHz to 600 MHz

  • Easy to connect OLED display.

  • Convenient and fast control with an encoder

  • The synthesizer is capable to generate sine wave.

  • The software allows you to select and configure the frequency of the clock generator through the user menu (without the need to recompile the program).

  • Any settings can be stored in non-volatile EEPROM memory (located at Arduino Mega).

  • Basic settings are applied and saved automatically.

  • This shield support overclocking the AD9959 core up to 600 MHz.

  • DDS AD9959 Shield has ability to generate a signal up to 225 MHz (to suppress harmonics, it is recommended to overclock the AD9959 for frequencies above 200 MHz).

The switching of clock sources:

The switching of clock sources is performed through the clock menu and is handled by an onboard software-controlled switch. It does not require the installation or removal of any components on the board to switch between clock sources: TCXO/OCXO, External TCXO/OCXO or External Oscillator.

List of Serial Port Commands:

Starting with version 1.21, the ability to control via the serial port has been added.

C — Set the current output Channel: (0 — 3)
F — Sets Frequency in Hz (100000 — 225000000)
A — Sets the power (Amplitude) level of the selected channel in dBm (-60 — -7)
P — Sets the Phase of the selected channel in dBm (0 — 360)
M — Gets Model
E - Enable Outputs (ALL)
D - Disable Outputs (ALL)
V — Gets Firmware Version
h — This Help
; — Commands Separator

Example:
C0;F100000;A-10
Sets the Frequency to 100 kHz, and Output Power (Amplitude) to -10 dBm on Channel 0 (RF OUT0).
Any number of commands in any order is allowed, but the very first command must be "C"

Serial Port Settings:

Speed - 115200 Bouds
Data Bits - 8
Stop Bits - 1
Parity - No
DTR - OFF

Windows:

An example of setting up a serial port in the Windows console:

  mode COM3 baud=115200 DTR=OFF Data=8

Usage example:

  echo F100000000 > COM3

Ubuntu 22.04:

An example of setting up a serial port in the Ubuntu:

  sudo usermod -aG dialout $USER_NAME$
  sudo chmod a+rw /dev/ttyUSB0
  sudo stty -F /dev/ttyUSB0 115200 cs8 ixoff -hupcl -echo

Usage example:

  echo "F100000000" > /dev/ttyUSB0