JD GarageDIY Plasma #1681
Description
$0=10.0 ; Step pulse time, microseconds
$1=255 ; Step idle delay, milliseconds
$2=0 ; Step pulse invert, mask
$3=5 ; Step direction invert, mask
$4=0 ; Invert step enable pin, boolean
$5=3 ; Invert limit pins, boolean/mask
$6=1 ; Invert probe pin, boolean
$9=1 ; PWM Spindle as bitfield where setting bit 0 enables the rest
$10=511 ; Status report options, mask
$11=0.010 ; Junction deviation, millimeters
$12=0.002 ; Arc tolerance, millimeters
$13=0 ; Report in inches, boolean
$14=0 ; Limit pins invert, mask
$15=0 ; Coolant pins invert, mask
$16=0 ; Spindle pins invert, mask
$17=0 ; Control pins pullup disable, mask
$18=0 ; Limit pins pullup disable, mask
$19=0 ; Probe pin pullup disable, boolean
$20=0 ; Soft limits enable, boolean
$21=0 ; Hard limits enable, boolean
$22=0 ; Homing cycle enable, boolean (Grbl) / mask (GrblHAL)
$23=0 ; Homing direction invert, mask
$24=25.0 ; Homing locate feed rate, mm/min
$25=500.0 ; Homing search seek rate, mm/min
$26=250 ; Homing switch debounce delay, milliseconds
$27=1.000 ; Homing switch pull-off distance, millimeters
$28=0.100 ; G73 retract distance, in mm
$29=0.0 ; Step pulse delay (ms)
$30=1000.000 ; Maximum spindle speed, RPM
$31=0.000 ; Minimum spindle speed, RPM
$32=0 ; Laser-mode enable, boolean
$33=5000.0 ; Spindle PWM frequency
$34=0.0 ; Spindle off Value
$35=0.0 ; Spindle min value
$36=100.0 ; Spindle max value
$37=0 ; Stepper deenergize mask
$39=1 ; Enable printable realtime command characters, boolean
$40=0 ; Apply soft limits for jog commands, boolean
$41=0 ; Parking cycle as bitfield where setting bit 0 enables the rest
$42=2 ; Parking axis
$43=1 ; Homing passes
$44=4 ; Homing cycle 1
$45=3 ; Homing cycle 2
$46=0 ; Homing cycle 3
$56=5.0 ; Parking pull-out distance in mm
$57=100.0 ; Parking pull-out rate in mm/min
$58=-5.0 ; Parking target in mm
$59=500.0 ; Parking fast rate in mm/min
$60=0 ; Restore overrides
$61=0 ; Safety door options as bitfield
$62=0 ; Sleep Enable
$63=3 ; Feed Hold Actions
$64=0 ; Force Init Alarm
$65=0 ; Require homing sequence to be executed at startup
$70=79 ; Network Services
$73=1 ; Wifi Mode
$74= ; Wifi network SSID
$75= ; Wifi network PSK
$100=40.00000 ; X-axis steps per millimeter
$101=40.00000 ; Y-axis steps per millimeter
$102=200.00000 ; Z-axis steps per millimeter
$110=12500.000 ; X-axis maximum rate, mm/min
$111=12500.000 ; Y-axis maximum rate, mm/min
$112=3000.000 ; Z-axis maximum rate, mm/min
$120=700.000 ; X-axis acceleration, mm/sec^2
$121=700.000 ; Y-axis acceleration, mm/sec^2
$122=700.000 ; Z-axis acceleration, mm/sec^2
$130=200.000 ; X-axis maximum travel, millimeters
$131=200.000 ; Y-axis maximum travel, millimeters
$132=20.000 ; Z-axis maximum travel, millimeters
$320=cutty ; Hostname, max: 64
$322=192.168.5.1 ; IP Address
$323=192.168.5.1 ; Gateway
$324=255.255.255.0 ; Netmask
$325=23 ; Telnet port
$326=80 ; HTTP port
$327=81 ; Websocket port
$328=21 ; unknown
$337= ; WiFi Access Point (AP) BSSID
$341=0 ; Tool Change Mode
$342=30.0 ; Tool Change probing distance
$343=25.0 ; Tool Change Locate Feed rate
$344=200.0 ; Tool Change Search Seek rate
$345=200.0 ; Tool Change Probe Pull Off rate
$346=1 ; Restore position after M6 as boolean
$370=4 ; Invert I/O Port Inputs (mask)
$384=0 ; Disable G92 Persistence
$392=4.0 ; Spindle on delay in s
$393=1.0 ; Coolant on delay in s
$398=100 ; Planner buffer blocks
$481=0 ; Autoreport interval in ms
$484=1 ; Unlock required after E-Stop as boolean
$486=0 ; Unlock required after E-Stop as boolean
$650=0 ; File systems options as bitfield
$I=custom