-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathprinter.cfg
186 lines (161 loc) · 4.14 KB
/
printer.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
# This file contains pin mappings for the stock 2020 Creality Ender 3
# V2. To use this config, during "make menuconfig" select the
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
# communication.
# If you prefer a direct serial connection, in "make menuconfig"
# select "Enable extra low-level configuration options" and select
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
# cable used for the LCD module as follows:
# 3: Tx, 4: Rx, 9: GND, 10: VCC
# Flash this firmware by copying "out/klipper.bin" to a SD card and
# turning on the printer with the card inserted. The firmware
# filename must end in ".bin" and must not match the last filename
# that was flashed.
# See docs/Config_Reference.md for a description of parameters.
# <---------------------- MAINSAIL ---------------------->
[include mainsail.cfg]
# <---------------------- STEPPER ---------------------->
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 39.653035935563816604708798017348
endstop_pin: ^PA5
position_endstop: 0
position_max: 245
homing_speed: 50
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 39.751552795031055900621118012422
endstop_pin: ^PA6
position_endstop: 0
position_max: 235
homing_speed: 50
[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 7.8953861337281026400197384653343
endstop_pin: probe: z_virtual_endstop #^PA7
#position_endstop: 0.0
position_max: 250
position_min: -3
# <---------------------- EXTRUDER/HOTEND ---------------------->
[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
#control: pid
# tuned for stock hardware with 200 degree Celsius target
#pid_Kp: 21.527
#pid_Ki: 1.063
#pid_Kd: 108.982
min_temp: 0
max_temp: 245
# <---------------------- BED ---------------------->
[heater_bed]
heater_pin: PA2
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
#control: pid
# tuned for stock hardware with 50 degree Celsius target
#pid_Kp: 54.027
#pid_Ki: 0.770
#pid_Kd: 948.182
# tuned for stock hardware with 80 degree Celsius target
min_temp: 0
max_temp: 130
# <---------------------- MCU ---------------------->
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
# <---------------------- PRINTER ---------------------->
[printer]
kinematics: cartesian
max_velocity: 300
max_accel: 2000
max_z_velocity: 5
max_z_accel: 100
# <---------------------- FAN ---------------------->
[fan]
pin: PA0
# <---------------------- PROBE ---------------------->
[bltouch]
sensor_pin: ^PB1
control_pin: PB0
x_offset: -44
y_offset: -7
z_offset: 0.18
samples: 2
samples_tolerance: 0.100
samples_tolerance_retries: 3
[safe_z_home]
home_xy_position: 154, 117 # Change coordinates to the center of your print bed
z_hop: 10 # Move up 10mm
z_hop_speed: 5
[bed_mesh]
speed: 120
horizontal_move_z: 5
mesh_min: 15, 15
mesh_max: 200, 200
probe_count: 5,3
algorithm: bicubic
fade_start: 1
fade_end: 10
fade_target: 0
[screws_tilt_adjust]
screw1: 70.5,37.5
screw1_name: front left screw
screw2: 240,37.5
screw2_name: front right screw
screw3: 240,207.5
screw3_name: rear right screw
screw4: 70.5,207.5
screw4_name: rear left screw
horizontal_move_z: 10
speed: 50
screw_thread: CW-M4
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 75.815
#*# pid_ki = 1.858
#*# pid_kd = 773.317
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 23.004
#*# pid_ki = 1.153
#*# pid_kd = 114.730
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# -0.077720, -0.080188, -0.119664, -0.159141, -0.165310
#*# -0.033309, -0.055514, -0.094991, -0.130767, -0.086356
#*# -0.057982, -0.086356, -0.125833, -0.152973, -0.096225
#*# tension = 0.2
#*# min_x = 14.99
#*# algo = bicubic
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 14.99
#*# x_count = 5
#*# max_y = 200.0
#*# mesh_x_pps = 2
#*# max_x = 200.0