Vendor Notes and hidden passwords!

[jazzmonger]

I got this from a helpful tech support person. Notice the protected password options settings!!

Pellet Stove Notes
Rev PHX20211021.5
To adjust the Auger (Pellet Drop Rate Settings) Without the App
• Cycle using the “Flame” button between settings P1, P2, P3, and P4
• P1 is the fastest setting
• P4 is the slowest setting

To adjust the fans for a better burn on the Pellet Drop settings
• Press and hold the “Wrench” button for two (2) seconds
• Press the “thumbs up” to get to cycle to each of the Pellet Drop Rate Settings
• Adjust the “S” for Exhaust/burn rate Venting Fan and “F” for Room Blower Fan settings using the arrow keys
• Use the “Clock” button to switch between “S” and “F”
o The lower the setting the slower the fan
o Only change settings by a few numbers at a time

To Change the Time – Runs on 24-Hour Clock
• Press and hold the “Wrench” button for two (2) seconds
• Use the “Thumbs Up” button to cycle to the “Modify Clock” Setting
• Use the “Clock” button to switch between Hours and Minutes
• Use the “Arrow Up” and “Arrow Down” buttons to change the current selection
• Use the “Thumbs Up” button to confirm the time set

To Program Automatic On and Off Without the App
• Press and hold the “Wrench” button for two (2) seconds
• Cycle through the settings using the “Thumbs Up” button until you find the different days of the week
• Use the “clock” button to change between options (The screen with 24 little boxes)
• Use the “Arrow” buttons to adjust if on or off for each day
• A Tall Box is for “On” and the Short Box is for “Off”
• Each box is for an hour of the day, the first box is 00:00 (Midnight) and the last box is for 23:00 (11PM)

Using the “Wrench” Button again will take you out of the settings menu

ECO modes
​Changing Eco Modes
• Press and hold the “Wrench” Button until the heater beeps
• Press (Do Not Hold) the “Thumbs Up” button seven (7) times to cycle to the screen that reads “ECO Mode” on the top line
• Press “Clock” Button to switch between the selected Eco Modes
• Press “Wrench” Button to leave the settings menu.
​ECO1
• Unit will run until desired temperature is reached
• Once temperature is reached, unit will go through shut down
• Stove will relight when thermostat reads the temperature is 3 degrees below the set temp setting
• The stove will go into stabilization mode and run until it reaches set temperature
• Cycle will repeat
ECO2
• Stove will run even if desired temperature is reached
• When temperature is reached the unit will slow the pellet drop rate to P4 form Px
o In some cases, the temperature in the room will continue to raise
• Once the thermostat reads 3 degrees below set temp it will change to a faster setting (P1 or Px) to raise the temperature
Disabling Wi-Fi:
• Press and hold the up arrow until it asks for a 4-digit password.
• Use the arrow keys and clock button to input 1109 as the password.
• Thumbs-up to confirm, and then press the thumbs-up 17 times to get to the Wi-Fi enabled option. (Open or Closed)
• Press clock button to switch over to the “closed” setting.
• Thumbs up one more time and then the wrench button will take you out of the password protected settings menu.

Switching between Fahrenheit and Celsius:
• Press and hold the up arrow until it asks for a 4-digit password.
• Use the arrow keys and clock button to input 1109 as the password.
• Press Thumbs-up to confirm, and then press the thumbs-up 18 more times to get to the Temperature Type.
o It will show a F for Fahrenheit and a C for Celsius
• Press clock button to switch over to the desired readout setting.
• Press the wrench button to take you out of the password protected settings menu.

Understanding the Error codes

• Temperature Sensor #1 is the exhaust sensor (PN 66609
• Temperature Sensor #2 is the hopper safety sensor (PN 66613)
• Temperature Sensor #3 is the room sensor (PN 66616)

Venting Requirements
• All of our stoves can be vented horizontally or vertically.
• The venting must be designed for pellet stoves, labelled as PL or L
o Pellet stove venting is double wall
• If being installed in a mobile/trailer home, the fresh air intake kit needs to be installed
• UL 103 HT PL venting is only required for installation in mobile/trailer homes
o If 3-inch venting is not available, installer can use an adapter to use larger venting
o All other installations can use UL 641 PL venting
​
MISC.
• Fuse: 75AL250V or .75 AMP/ 250 Volts
• Auger does make a slight growling noise when in operation
• Some pellet loss is to be expected, make sure burn box is positioned correctly
• If pellets are building up in burn box, increase exhaust fan speed (S) until proper burn is achieved.
• 120v/300w going to the ignitor
• Press and hold the “Clock” button to get the auger to spin while unit is powered on
o Doing this will help hasten the lighting phase when done before a cold start.
• The 4-digit password is 1109
• Restoring Pellet Stoves to factory default does not reset WIFI Connection