DashBox Communication

[traveler2100]

I've installed the integration and I am trying to see the forwarded packets from the Dashbox instead of the GEM. I understood from Brultech support that it may be possible with this version. I installed on port 8000 and configured the DB to forward on 8000 but cannot see the packets. Is this possible? THanks

[traveler2100]

After some restarts, I am seeing the DB and getting data. I only have 6 channels being used and no pulse counters but I am getting values on 30 channels and 4 pulse counters. I only want live watts from the 6 channels but haven't discovered how to configure channels without YAML.

[jkeljo]

I'm away from my computer at the moment so I can't give you the exact path to follow, but in the Home Assistant Settings there's a place where you can view entities and enable/disable them in bulk.

[traveler2100]

Thanks. The issue is all 30 channels have a value when they are empty on the DB, pulse counters also. I'm not sure what I am getting. I was looking for a place to set the units etc. I think the problem may be on the DB end. I'll work with it some more to see what I am actually sending and receiving. Thanks again.

[jkosharek]

I have the hacs-greeneye-monitor installed and configured for port 8000, on Dashbox I configured Packet Forward to the HASS IP on port 8000. I have restarted HA several times, does the Dashbox need to be restarted?

[jkeljo]

Yes, dashboxes should work with that setup.

I don't have a dashbox, so I don't really know, but presumably it couldn't hurt to reboot. Might be worth asking in the Brultech forums.

If you want, file a new issue here with all of the info that the bug report issue workflow will request (version, debug logs, etc.) and we can at least make sure there's nothing going obviously wrong on the HA side.

[jkosharek]

@jkeljo I posted on the DB forum about the settings needed on the DB side to make this work. I did reboot and it doesn't seem like HA is seeing anything from DB. What is the format HA is looking for?

@traveler2100 what settings do your GEMs have for packet send, and did you put anything in the 'Add Command' section of the 'Packet Forward' on DB settings?

[jkeljo]

Any of the binary formats will do. BIN32-ABS, BIN32-NET, etc.

[adamgreenberg07]

I've been trying to get the HA plugin to work too. I just got data to flow from the dashbox to HA. Set the destinations server to HA IP, port 8001 (which is also the same port that the GEM is using to send to the dashbox. Not sure if that matters or not), persist is on, nothing in add command. On HA, I've added a hub, set the port to the same 8001. The breakthrough for me was when I changed the data format that the GEM is sending to the dashbox to Bin-32 NET.

The data looks wrong though. Each channel is reading a large negatitve number -152,966.360694444 kWh for example. I think it has something to do with the add command setting on the dashbox, but am not sure. I've asked in the brultech forum, but if anyone here knows or has other ideas as to what might be wrong, would love to hear.

[jkeljo]

Are the power readings off as well? -152,000kWh is a lot, but not out of the realm of possibility if that circuit is your whole house or your solar panels and you've had the GEM installed for 7-10 years.

[adamgreenberg07]

Ok. I think I've figured more out. This set of readings was not disabled by default. I now see that there are 3 readings for each of the channels (excluding pulse and temp). I've enabled the other two. Amps, Watts, Kwh. It was this third Kwh one that I was seeing when I wrote last night. I now see how to enable the others to get the other readings.

That said, what is the purpose of this Kwh reading? Is it the lifetime amount of power ever recorded by that channel? If so, how are others using it or are others disabling it?

[jkosharek]

Kwh is a total for that CT, useful for a day or month calculation of power consumption. They can be reset on a schedule via a command ^^^SYSRSTA (all counters) or ^^^SYSRSTP (pulse counters), or in the Gem web interface

[adamgreenberg07]

Can you share a little more instruction on how to issue the ^^^SYSRSTA command for the day or month.

[jkosharek]

I am waiting for a response from brultech/gem support on where exactly that would be run. I will follow up on this case when I have the settings working for Gems and Dashbox to get my setup working (Gem > Network > Dashbox > HA).

[jkeljo]

Home Assistant's energy dashboard can use the kWh sensors to report your energy production (if you have solar) and usage over time. If you want to set that up I would recommend against resetting those values on a schedule because it would likely result in that showing incorrect data.

[jkeljo]

If resetting on a schedule is desired, that is conceivably a feature that could be added to this integration, in which case it would be able to tell Home Assistant when it does a reset so that the values continue to appear correctly in the energy dashboard.

It's not super necessary from Home Assistant perspective because it already knows how to show hourly/daily/monthly/yearly consumption and takes ages for the counters to roll over, but if you need it for something else please file a feature request and I can look at implementing it (or advise someone on doing so).