[prim_esc_receiver] Register esc_req_o to avoid potential CDC issues

This is related to #24119.

Signed-off-by: Pirmin Vogel <[email protected]>

Author: vogelpi

hw/ip/prim/dv/prim_esc/tb/prim_esc_tb.sv

@@ -110,6 +110,8 @@ module prim_esc_tb;
     // Drive random length of esc_req and check `esc_req_out` and `integ_fail` outputs.
     main_clk.wait_clks($urandom_range(1, 20));
     if (integ_fail)   test_error("Esc_req unexpected signal integrity error!");
+    // Wait for the escalation request to pass through the output register.
+    main_clk.wait_clks(1);
     if (!esc_req_out) test_error("Esc_req did not set esc_req!");
     esc_req = 0;
 
@@ -148,6 +150,8 @@ module prim_esc_tb;
     `DV_SPINWAIT(wait (integ_fail == 1);, , , "Wait for esc_tx.esc_n integ_fail timeout");
     main_clk.wait_clks(1);
     release esc_tx.esc_n;
+    // Wait for the escalation request to pass through the output register.
+    main_clk.wait_clks(1);
     // Wait #1ps to avoid a race condition on clock edge.
     #1ps;
     if (!esc_req_out) test_error("Signal integrity error should set esc_req!");
@@ -161,6 +165,8 @@ module prim_esc_tb;
     `DV_SPINWAIT(wait (integ_fail == 1);, , , "Wait for esc_rx.resp_n integ_fail timeout");
     main_clk.wait_clks(1);
     release esc_rx.resp_n;
+    // Wait for the escalation request to pass through the output register.
+    main_clk.wait_clks(1);
     // Wait #1ps to avoid a race condition on clock edge.
     #1ps;
     if (!esc_req_out) test_error("Signal integrity error should set esc_req!");
@@ -176,8 +182,12 @@ module prim_esc_tb;
     release esc_tx.esc_n;
     // Wait #1ps to avoid a race condition on clock edge.
     #1ps;
-    if (!esc_req_out) test_error("Signal integrity error should set esc_req!");
     if (ping_ok)      test_error("Ping error!");
+    // Wait for the escalation request to pass through the output register.
+    main_clk.wait_clks(1);
+    // Wait #1ps to avoid a race condition on clock edge.
+    #1ps;
+    if (!esc_req_out) test_error("Signal integrity error should set esc_req!");
     ping_req = 0;
 
     $display("[prim_esc_seq] Escalation esc_p/n integrity sequence during ping request finished!");
@@ -191,7 +201,7 @@ module prim_esc_tb;
         // After one ping_req, esc_receiver will start a counter to expect next ping_req. If the
         // counter reaches its max value but no ping_req has been received, design will set
         // `esc_req_out` signal.
-        main_clk.wait_clks(TIMEOUT_CYCLES + 1);
+        main_clk.wait_clks(TIMEOUT_CYCLES + 2);
         if (!esc_req_out) test_error("Design failed to detect ping request timeout!");
       end
       begin
@@ -200,6 +210,8 @@ module prim_esc_tb;
         main_clk.wait_clks(2);
         ping_req = 0;
         if (integ_fail)  test_error("Ping_req unexpected signal integrity error!");
+        // Wait for the escalation request to pass through the output register.
+        main_clk.wait_clks(1);
         if (esc_req_out) test_error("Ping request should not set esc_req_out!");
       end
     join

hw/ip/prim/fpv/vip/prim_esc_rxtx_assert_fpv.sv

@@ -103,11 +103,11 @@ module prim_esc_rxtx_assert_fpv
       !rst_ni ||
       error_present)
 
-  // check correct transmission of escalation within 0-1 cycles
+  // check correct transmission of escalation within 1-2 cycles
   `ASSERT(EscCheck_A,
       ##1 esc_req_i
       |->
-      ##[0:1] esc_req_o,
+      ##[1:2] esc_req_o,
       clk_i,
       !rst_ni ||
       error_present)
@@ -155,7 +155,7 @@ module prim_esc_rxtx_assert_fpv
       !esc_req_o ##1
       !ping_req_i [*0 : 2**TimeoutCntDw - 4]
       |->
-      !esc_req_o,
+      ##1 !esc_req_o,
       clk_i,
       !rst_ni ||
       error_d ||
@@ -169,7 +169,7 @@ module prim_esc_rxtx_assert_fpv
       !esc_req_o ##1
       !ping_req_i [* 2**TimeoutCntDw - 3 : $]
       |->
-      esc_req_o,
+      ##1 esc_req_o,
       clk_i,
       !rst_ni ||
       error_d ||

hw/ip/prim/rtl/prim_esc_receiver.sv

@@ -126,11 +126,21 @@ module prim_esc_receiver
   // - requested via the escalation sender/receiver path,
   // - the ping monitor timeout is reached,
   // - the two ping monitor counters are in an inconsistent state.
-  logic esc_req;
+  // Register the escalation request to avoid potential CDC issues downstream.
+  logic esc_req, esc_req_d, esc_req_q;
+  assign esc_req_d = esc_req || (&timeout_cnt) || timeout_cnt_error;
+  always_ff @(posedge clk_i or negedge rst_ni) begin
+    if (!rst_ni) begin
+      esc_req_q <= 1'b0;
+    end else begin
+      esc_req_q <= esc_req_d;
+    end
+  end
+
   prim_sec_anchor_buf #(
     .Width(1)
   ) u_prim_buf_esc_req (
-    .in_i(esc_req || (&timeout_cnt) || timeout_cnt_error),
+    .in_i (esc_req_q),
     .out_o(esc_req_o)
   );
 
@@ -257,7 +267,7 @@ module prim_esc_receiver
   `ASSERT(SigIntCheck0_A, esc_tx_i.esc_p == esc_tx_i.esc_n |=> esc_rx_o.resp_p == esc_rx_o.resp_n)
   `ASSERT(SigIntCheck1_A, esc_tx_i.esc_p == esc_tx_i.esc_n |=> state_q == SigInt)
   // auto-escalate in case of signal integrity issue
-  `ASSERT(SigIntCheck2_A, esc_tx_i.esc_p == esc_tx_i.esc_n |=> esc_req_o)
+  `ASSERT(SigIntCheck2_A, esc_tx_i.esc_p == esc_tx_i.esc_n |=> esc_req_d)
   // correct diff encoding
   `ASSERT(DiffEncCheck_A, esc_tx_i.esc_p ^ esc_tx_i.esc_n |=> esc_rx_o.resp_p ^ esc_rx_o.resp_n)
   // disable in case of signal integrity issue
@@ -271,10 +281,10 @@ module prim_esc_receiver
   // detect escalation pulse
   `ASSERT(EscEnCheck_A,
           esc_tx_i.esc_p && (esc_tx_i.esc_p ^ esc_tx_i.esc_n) && state_q != SigInt
-      ##1 esc_tx_i.esc_p && (esc_tx_i.esc_p ^ esc_tx_i.esc_n) |-> esc_req_o)
+      ##1 esc_tx_i.esc_p && (esc_tx_i.esc_p ^ esc_tx_i.esc_n) |-> esc_req_d)
   // make sure the counter does not wrap around
   `ASSERT(EscCntWrap_A, &timeout_cnt |=> timeout_cnt != 0)
   // if the counter expires, escalation should be asserted
-  `ASSERT(EscCntEsc_A, &timeout_cnt |-> esc_req_o)
+  `ASSERT(EscCntEsc_A, &timeout_cnt |-> esc_req_d)
 
 endmodule : prim_esc_receiver