| layout | title |
|---|---|
documentation |
ST814 - ZWave |
{% include base.html %}
This describes the Z-Wave device ST814, manufactured by Everspring with the thing type UID of everspring_st814_00_000.
The device is in the category of Sensor, defining Device used to measure something.
The ST814 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The ST814 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.
The Temperature/Humidity Detector is a Z-WaveTM enabled device which is fully compatible with any Z-WaveTM enabled network. Z-WaveTM enabled devices displaying the Z-WaveTM logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturer’s Z-WaveTM enabled networks. Inclusion of this detector on other manufacturer’s Wireless Controller menu allows remote operation of connected modules when the detector is triggered.
The Temperature/Humidity Detector is designed to monitor the current temperature and humidity of ambient environment. The reading of temperature/humidity can be reported to you on a regular base at your disposal. If temperature/humidity reaches set points, the detector will send alerts to associated devices for further execution. Since sudden temperature/humidity change may cause health problems to people such as elderly or very young children, Temp./Humid. Detector provides you most up-to-date temperature and humidity reading for you to watch your family’s health.
One of function key (C/F/L) is used to carry out inclusion, exclusion, association and reset. When the detector is first powered up, the reading in RF mode is 00 which implies that it hasn’t been allocated a node ID and cannot work with Z-WaveTM enabled devices. The Temp./Humid. Detector will stay “awake” for 10 minutes when power is first applied to allow time for configuration.
- Pressing key 3 times within 1.5 seconds will enter inclusion mode
One of function key (C/F/L) is used to carry out inclusion, exclusion, association and reset. When the detector is first powered up, the reading in RF mode is 00 which implies that it hasn’t been allocated a node ID and cannot work with Z-WaveTM enabled devices. The Temp./Humid. Detector will stay “awake” for 10 minutes when power is first applied to allow time for configuration.
- Pressing key 3 times within 1.5 seconds will enter exclusion mode
The ST814 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.
The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.
- Pressing key 3 times within 1.5 seconds will wake the device
The following table summarises the channels available for the ST814 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Binary Switch | switch_binary | switch_binary | Switch | Switch |
| Sensor (relative humidity) | sensor_relhumidity | sensor_relhumidity | Humidity | Number |
| Sensor (temperature) | sensor_temperature | sensor_temperature | Temperature | Number:Temperature |
| Temperature trigger ON value | config_decimal | config_decimal | Number | |
| Temperature trigger OFF value | config_decimal | config_decimal | Number | |
| Humidity trigger ON value | config_decimal | config_decimal | Number | |
| Humidity trigger OFF value | config_decimal | config_decimal | Number | |
| Battery Level | battery-level | system.battery_level | Battery | Number |
| Sensor (temperature) 1 | sensor_temperature1 | sensor_temperature | Temperature | Number:Temperature |
| Sensor (relative humidity) 2 | sensor_relhumidity2 | sensor_relhumidity | Humidity | Number |
This channel will be set to ON when the temperature or humidity level in configuration parameters 2 and 4 are reached. The channel will be set to OFF when the temperature or humidity level in configuration parameters 3 and 5 are reached.
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Indicates the current relative humidity.
The sensor_relhumidity channel is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
Indicates the current temperature.
The sensor_temperature channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
This is the temperature that, when reached, will cause the device to send an ON command on the switch_binary channel.
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
This is the temperature that, when reached, will cause the device to send an OFF command on the switch_binary channel.
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
This is the humidity level that, when reached, will cause the device to send an ON command on the switch_binary channel.
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
This is the humidity level that, when reached, will cause the device to send an OFF command on the switch_binary channel.
Generic class for configuration parameter.
The config_decimal channel is of type config_decimal and supports the Number item.
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
Indicates the current temperature.
The sensor_temperature1 channel is of type sensor_temperature and supports the Number:Temperature item and is in the Temperature category.
Indicates the current relative humidity.
The sensor_relhumidity2 channel is of type sensor_relhumidity and supports the Number item and is in the Humidity category. This is a read only channel so will only be updated following state changes from the device.
The following table provides a summary of the 8 configuration parameters available in the ST814. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Basic Set Level | Set basic set value to be on or off |
| 2 | Temperature Trigger ON value | Temperature level when a ON command is sent out. Set to 99 to disable. |
| 3 | Temperature Trigger OFF value | Temperature level when a OFF command is sent out. Set to 99 to disable. |
| 4 | Humidity Trigger ON value | Humidity level when a ON command is sent out. Set to 99 to disable. |
| 5 | Humidity Trigger OFF value | Humidity level when a OFF command is sent out. Set to 99 to disable. |
| 6 | Auto report time | Sets the time interval when a sensor report is sent |
| 7 | Auto report temperature | Sets the temperature change causing a sensor report. |
| 8 | Auto report humidity | Sets the humidity change causing a sensor report. |
| Wakeup Interval | Sets the interval at which the device will accept commands from the controller | |
| Wakeup Node | Sets the node ID of the device to receive the wakeup notifications |
Set basic set value to be on or off 0=Disable
1-99=Use Value The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
| 1 | Test |
The manufacturer defined default value is 99.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Temperature level when a ON command is sent out. Set to 99 to disable.
The following option values may be configured -:
| Value | Description |
|---|---|
| 99 | Disable |
The manufacturer defined default value is 99 (Disable).
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Temperature level when a OFF command is sent out. Set to 99 to disable.
The following option values may be configured -:
| Value | Description |
|---|---|
| 99 | Disable |
The manufacturer defined default value is 99 (Disable).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Humidity level when a ON command is sent out. Set to 99 to disable.
The following option values may be configured -:
| Value | Description |
|---|---|
| 99 | Disable |
The manufacturer defined default value is 99 (Disable).
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Humidity level when a OFF command is sent out. Set to 99 to disable.
The following option values may be configured -:
| Value | Description |
|---|---|
| 99 | Disable |
The manufacturer defined default value is 99 (Disable).
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Sets the time interval when a sensor report is sent 0 = Disable
1 min - 1439 min = Auto report periodically The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_6_2 and is of type INTEGER.
Sets the temperature change causing a sensor report. 0 = Disable
1 - 70 = Auto report on temperature change The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Sets the humidity change causing a sensor report. 0 = Disable
5 - 70 = Auto report on humidity change The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disable |
The manufacturer defined default value is 0 (Disable).
This parameter has the configuration ID config_8_1 and is of type INTEGER.
The wakeup interval sets the period at which the device will listen for messages from the controller. This is required for battery devices that sleep most of the time in order to conserve battery life. The device will wake up at this interval and send a message to the controller to tell it that it can accept messages - after a few seconds, it will go back to sleep if there is no further communications.
This setting is defined in seconds. It is advisable not to set this interval too short or it could impact battery life. A period of 1 hour (3600 seconds) is suitable in most instances.
Note that this setting does not affect the devices ability to send sensor data, or notification events.
This parameter has the configuration ID wakeup_interval and is of type INTEGER.
When sleeping devices wake up, they send a notification to a listening device. Normally, this device is the network controller, and normally the controller will set this automatically to its own address. In the event that the network contains multiple controllers, it may be necessary to configure this to a node that is not the main controller. This is an advanced setting and should not be changed without a full understanding of the impact.
This parameter has the configuration ID wakeup_node and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ST814 supports 2 association groups.
Association group 1 supports 1 node.
Association group 2 supports 3 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2 | Linked to BASIC |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_WAKE_UP_V2 | |
| COMMAND_CLASS_ASSOCIATION_V1 | |
| COMMAND_CLASS_VERSION_V1 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2 | Linked to BASIC |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_MULTILEVEL_V2 | Linked to BASIC |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.