layout	title
documentation	GE/Jasco 14299 - ZWave

{% include base.html %}

GE/Jasco 14299 GE/Jasco In-Wall 1000W Incandescent Smart Dimmer

This describes the Z-Wave device GE/Jasco 14299, manufactured by Jasco Products with the thing type UID of ge_14299_00_000.

The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.

The GE/Jasco 14299 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. Refer to the Wakeup Information section below for further information.

Overview

Basic operation

The connected light can be turned ON/OFF and adjust dim levels in two ways:

Manually from the front panel of the In-Wall Dimmer.
Remotely with a Z-Wave Controller .

Manual control

The Front Panel Rocker Dimmer allows the user to turn ON/OFF the connected fixture.

To turn the connected fixture ON: press and release the top of the rocker.
To turn the connected fixture OFF: press and release the bottom of the rocker.

Adjust dim level

To increase brightness: press and hold the top of the rocker.
To decrease brightness: press and hold the bottom of the rocker.

Disable / Enable LED

Press UP three (3) times then quickly press and release DOWN one (1) time.
Repeat to disable/enable LED.

This device supports Association Command Class (3 Groups)

Association Group 1 supports Lifeline, Switch Multilevel Report
Association Group 2 supports Basic Set and is controlled by pressing the On or Off button with the local load
Association Group 3 supports Basic Set and is controlled by double pressing the On or Off button
Each Association Group supports 5 total nodes

Inclusion Information

Adding your device to a Z-Wave network

Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
Once the controller is ready to add your device, press and release the top or bottom of the wireless smart switch (rocker) to add it in the network.

Please reference the controller's manual for instructions.

Exclusion Information

To remove and reset the device

Follow the instructions for your Z-Wave certified controller to remove a device from the Z-Wave network.
Once the controller is ready to remove your device, press and release the top or bottom of the wireless smart dimmer (rocker) to remove it from the network.

To return your switch to factory defaults:

Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three (3) times. The LED will flash ON/OFF 5 times when completed successfully. Note: This should only be used in the event your network’s primary controller is missing or otherwise inoperable.

Wakeup Information

The GE/Jasco 14299 does not permanently listen for messages sent from the controller - it will periodically wake up automatically to check if the controller has messages to send, but will sleep most of the time to conserve battery life. The wakeup period can be configured in the user interface - it is advisable not to make this too short as it will impact battery life - a reasonable compromise is 1 hour.

The wakeup period does not impact the devices ability to report events or sensor data. The device can be manually woken with a button press on the device as described below - note that triggering a device to send an event is not the same as a wakeup notification, and this will not allow the controller to communicate with the device.

Channels

The following table summarises the channels available for the GE/Jasco 14299 -:

Channel Name	Channel ID	Channel Type	Category	Item Type
Dimmer	switch_dimmer	switch_dimmer	DimmableLight	Dimmer
Scene Number	scene_number	scene_number		Number

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.

Scene Number

Triggers when a scene button is pressed.

The scene_number channel is of type scene_number and supports the Number item.

Device Configuration

The following table provides a summary of the 8 configuration parameters available in the GE/Jasco 14299. Detailed information on each parameter can be found in the sections below.

Param	Name	Description
3	LED Light	LED Light
4	Invert Switch	Invert Switch
7	Dim Steps	number of steps or levels
8	Dim Timing	timing of steps
9	Dim 2 Steps	number of steps or levels
10	Dim 2 Timing	timing of steps
11	Dim 3 Steps	number of steps or levels
12	Dim 3 Timing	timing of steps
	Switch All Mode	Set the mode for the switch when receiving SWITCH ALL commands

Parameter 3: LED Light

LED Light

The following option values may be configured -:

Value	Description
0	LED ON when load is OFF
1	LED ON when load is ON
2	LED always OFF

The manufacturer defined default value is 0 (LED ON when load is OFF).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Invert Switch

Invert Switch

The following option values may be configured -:

Value	Description
0	Default
1	Invert Switch

The manufacturer defined default value is 0 (Default).

This parameter has the configuration ID config_4_1 and is of type INTEGER.