| layout | title |
|---|---|
documentation |
Lumi LM-S4ZW (C-L) - ZWave |
{% include base.html %}
This describes the Z-Wave device Lumi LM-S4ZW (C-L), manufactured by Hogar Controls with the thing type UID of hogar_lmsxzwcl_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The Lumi LM-S4ZW (C-L) supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
4 Button Z-Wave Switch: 2 lights and 2 buttons for up/down blinds control.
- Operating Voltage: 100 - 240V/50Hz
- Operating Temperature: 0 - 50ºC
- Power: 700w/button
- Dimension: 125 x 95 x 34,1 mm (rectangular)
Touch and hold any key on the panel for more than 5 seconds. All indication lights will blinks in blue. At this point release the key, the touch panel will start inclusion process.
Touch and hold any key on the panel for more than 5 seconds. All indication lights will blinks blue in color. At this point release the key, the touch panel will start exclusion process.
The following table summarises the channels available for the Lumi LM-S4ZW (C-L) -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Switch 1 | switch_binary1 | switch_binary | Switch | Switch |
| Dimmer 1 | switch_dimmer1 | switch_dimmer | DimmableLight | Dimmer |
| Switch 2 | switch_binary2 | switch_binary | Switch | Switch |
| Dimmer 2 | switch_dimmer2 | switch_dimmer | DimmableLight | Dimmer |
| Switch 3 | switch_binary3 | switch_binary | Switch | Switch |
| Dimmer 3 | switch_dimmer3 | switch_dimmer | DimmableLight | Dimmer |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Switch the power on and off.
The switch_binary1 channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer1 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Switch the power on and off.
The switch_binary2 channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer2 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Switch the power on and off.
The switch_binary3 channel is of type switch_binary and supports the Switch item and is in the Switch category.
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer3 channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The Lumi LM-S4ZW (C-L) supports 9 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Basic Set
Association group 2 supports 5 nodes.
Switch Binary Set
Association group 3 supports 5 nodes.
Basic Set
Association group 4 supports 5 nodes.
Switch Binary Set
Association group 5 supports 5 nodes.
Basic Set
Association group 6 supports 5 nodes.
Switch Binary Set
Association group 7 supports 5 nodes.
Basic Set
Association group 8 supports 5 nodes.
Switch Binary Set
Association group 9 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.