layout	title
documentation	LHC5020 - ZWave

{% include base.html %}

LHC5020 DIN-rail module with 10 digital ouputs and 4 digital inputs

This describes the Z-Wave device LHC5020, manufactured by Logic Group with the thing type UID of logic_lhc5020_00_000.

The device is in the category of Radiator Control, defining Controls on radiators used to heat up rooms.

The LHC5020 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.

Overview

This device can be used for controlling standard floor heating valves

Inclusion Information

1.) Set your ZWave controller in inclusion mode

2.) Press the inclusion button on the LHC5020 device three times quickly

3.) The diode will blink to confirm the inclusion is done

Exclusion Information

1.) Set your ZWave controller in exclusion mode

2.) Press the inclusion button on the LHC5020 device three times quickly

3.) The diode will blink to confirm the exclusion is done

Reset the device

The device can be reset by holding down the inclusion button for 10 sec.

Channels

The following table summarises the channels available for the LHC5020 -:

Channel Name	Channel ID	Channel Type	Category	Item Type
Switch	switch_binary	switch_binary	Switch	Switch
Dimmer	switch_dimmer	switch_dimmer	DimmableLight	Dimmer
Switch 1	switch_binary1	switch_binary	Switch	Switch
Switch 2	switch_binary2	switch_binary	Switch	Switch
Switch 3	switch_binary3	switch_binary	Switch	Switch
Switch 4	switch_binary4	switch_binary	Switch	Switch
Switch 5	switch_binary5	switch_binary	Switch	Switch
Switch 6	switch_binary6	switch_binary	Switch	Switch
Switch 7	switch_binary7	switch_binary	Switch	Switch
Switch 8	switch_binary8	switch_binary	Switch	Switch
Switch 9	switch_binary9	switch_binary	Switch	Switch
Switch 10	switch_binary10	switch_binary	Switch	Switch
Switch 11	switch_binary11	switch_binary	Switch	Switch
Switch 12	switch_binary12	switch_binary	Switch	Switch
Switch 13	switch_binary13	switch_binary	Switch	Switch
Switch 14	switch_binary14	switch_binary	Switch	Switch

Switch

Switch the power on and off.

The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.

Dimmer

The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.

The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.

Switch 1

Switch the power on and off.

The switch_binary1 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 2

Switch the power on and off.

The switch_binary2 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 3

Switch the power on and off.

The switch_binary3 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 4

Switch the power on and off.

The switch_binary4 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 5

Switch the power on and off.

The switch_binary5 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 6

Switch the power on and off.

The switch_binary6 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 7

Switch the power on and off.

The switch_binary7 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 8

Switch the power on and off.

The switch_binary8 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 9

Switch the power on and off.

The switch_binary9 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 10

Switch the power on and off.

The switch_binary10 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 11

Switch the power on and off.

The switch_binary11 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 12

Switch the power on and off.

The switch_binary12 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 13

Switch the power on and off.

The switch_binary13 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Switch 14

Switch the power on and off.

The switch_binary14 channel is of type switch_binary and supports the Switch item and is in the Switch category.

Device Configuration

The following table provides a summary of the 13 configuration parameters available in the LHC5020. Detailed information on each parameter can be found in the sections below.

Param	Name	Description
1	Diode control	Diode control
2	Turn on/off voltage on input terminal 1	Turn on/off voltage on input terminal 1
3	Turn on/off voltage on input terminal 2	Turn on/off voltage on input terminal 2
4	Turn on/off voltage on input terminal 3	Turn on/off voltage on input terminal 3
5	Turn on/off voltage on input terminal 4	Turn on/off voltage on input terminal 4
6	Prel. filter time on input terminals	Preliminary filter time on input terminals
7	Threshold for triggering input	Threshold for triggering input
8	Threshold time for triggering input	Threshold time for triggering input
9	Function for input terminal 1	Function for input terminal 1
10	Function for input terminal 2	Function for input terminal 2
11	Function for input terminal 3	Function for input terminal 3
12	Function for input terminal 4	Function for input terminal 4
13	Central Scene notification	Central Scene notification

Parameter 1: Diode control

Diode control 0 Turned off

1 Turned on (Default)

2 Blinking 1 sec. interval

3 Blinking 0.5 sec. interval The following option values may be configured -:

Value	Description
0	Turned off
1	Turned on
2	Blinking 1 sec. interval
3	Blinking 0.5 sec. interval

The manufacturer defined default value is 1 (Turned on).

This parameter has the configuration ID config_1_1 and is of type INTEGER.

Parameter 2: Turn on/off voltage on input terminal 1

Turn on/off voltage on input terminal 1 If trigger devices on the input terminal needs external power supply, then turn of the voltage on the input terminal.

0 = Voltage off (use external power supply up to 10V)

1 = Voltage on (7.5V) The following option values may be configured -:

Value	Description
0	Off
1	On

The manufacturer defined default value is 1 (On).

This parameter has the configuration ID config_2_1 and is of type INTEGER.

Parameter 3: Turn on/off voltage on input terminal 2

Turn on/off voltage on input terminal 2 If trigger devices on the input terminal needs external power supply, then turn of the voltage on the input terminal.

0 = Voltage off (use external power supply up to 10V)

1 = Voltage on (7.5V) The following option values may be configured -:

Value	Description
0	Off
1	On

The manufacturer defined default value is 1 (On).

This parameter has the configuration ID config_3_1 and is of type INTEGER.

Parameter 4: Turn on/off voltage on input terminal 3

Turn on/off voltage on input terminal 3 If trigger devices on the input terminal needs external power supply, then turn of the voltage on the input terminal.

0 = Voltage off (use external power supply up to 10V)

1 = Voltage on (7.5V) The following option values may be configured -:

Value	Description
0	Off
1	On

The manufacturer defined default value is 1 (On).

This parameter has the configuration ID config_4_1 and is of type INTEGER.

Parameter 5: Turn on/off voltage on input terminal 4

Turn on/off voltage on input terminal 4 If trigger devices on the input terminal needs external power supply, then turn of the voltage on the input terminal.

0 = Voltage off (use external power supply up to 10V)

1 = Voltage on (7.5V) The following option values may be configured -:

Value	Description
0	Off
1	On

The manufacturer defined default value is 1 (On).

This parameter has the configuration ID config_5_1 and is of type INTEGER.

Parameter 6: Prel. filter time on input terminals

Preliminary filter time on input terminals Time in 10x milliseconds. E.g. 5 = 50 ms. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 5.

This parameter has the configuration ID config_6_1 and is of type INTEGER.

Parameter 7: Threshold for triggering input

Threshold for triggering input In 10x milliseconds, e.g. 5 = 50 ms, meaning that the voltage on the input terminals need to be stable for more than 50 ms behold the input is counted as activated. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 20.

This parameter has the configuration ID config_7_1 and is of type INTEGER.

Parameter 8: Threshold time for triggering input

Threshold time for triggering input Time in 10x miliseconds that an input need to be activated before it is counted as activated. E.g. 50 = 500 ms. Values in the range 0 to 255 may be set.

The manufacturer defined default value is 50.

This parameter has the configuration ID config_8_1 and is of type INTEGER.

Parameter 9: Function for input terminal 1

Function for input terminal 1 0 = Inactive

1 = Level controlled

2 = Back edge controlled

3 = Front edge controlled. Values in the range 0 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_9_1 and is of type INTEGER.

Parameter 10: Function for input terminal 2

Function for input terminal 2 0 = Inactive

1 = Level controlled

2 = Back edge controlled

3 = Front edge controlled. Values in the range 0 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_10_1 and is of type INTEGER.

Parameter 11: Function for input terminal 3

Function for input terminal 3 0 = Inactive

1 = Level controlled

2 = Back edge controlled

3 = Front edge controlled. Values in the range 0 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_11_1 and is of type INTEGER.

Parameter 12: Function for input terminal 4

Function for input terminal 4 0 = Inactive

1 = Level controlled

2 = Back edge controlled

3 = Front edge controlled. Values in the range 0 to 3 may be set.

The manufacturer defined default value is 1.

This parameter has the configuration ID config_12_1 and is of type INTEGER.

Parameter 13: Central Scene notification

Central Scene notification Send Central Scene notification when the 4 input terminals gets activated.

0 = Notification off

1 = Notification on Values in the range 0 to 1 may be set.

The manufacturer defined default value is 0.

This parameter has the configuration ID config_13_1 and is of type INTEGER.

Association Groups

Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.

The LHC5020 supports 14 association groups.

Group 1: Lifeline

The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Group 1 Gruppe 1 / 1

Lifeline. Gælder for hele modulet.

Maks. antal enheder i gruppen: 1

Gruppe 2 / 2

Sender Basic Report On / Off når udgang 1 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 1 supports 5 nodes.

Group 2: Group 2

Group 2 Enhed 2 (End Point 2)

Udgang 2

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 3

Sender Basic Report On / Off når udgang 2 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 2 supports 5 nodes.

Group 3: Group 3

Group 3 Enhed 3 (End Point 3)

Udgang 3

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 4

Sender Basic Report On / Off når udgang 3 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 3 supports 5 nodes.

Group 4: Group 4

Group 4 Enhed 4 (End Point 4)

Udgang 4

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 5

Sender Basic Report On / Off når udgang 4 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 4 supports 5 nodes.

Group 5: Group 5

Group 5 Enhed 5 (End Point 5)

Udgang 5

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 6

Sender Basic Report On / Off når udgang 5 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 5 supports 5 nodes.

Group 6: Group 6

Group 6 Enhed 6 (End Point 6)

Udgang 6

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 7

Sender Basic Report On / Off når udgang 6 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 6 supports 5 nodes.

Group 7: Group 7

Group 7 Enhed 7 (End Point 7)

Udgang 7

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 8

Sender Basic Report On / Off når udgang 7 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 7 supports 5 nodes.

Group 8: Group 8

Group 8 Enhed 8 (End Point 8)

Udgang 8

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 9

Sender Basic Report On / Off når udgang 8 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 8 supports 5 nodes.

Group 9: Group 9

Group 9 Enhed 9 (End Point 9)

Udgang 9

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 10

Sender Basic Report On / Off når udgang 9 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 9 supports 5 nodes.

Group 10: Group 10

Group 10 Enhed 10 (End Point 10)

Udgang 10

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 11

Sender Basic Report On / Off når udgang 10 bliver aktiveret.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for udgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Association group 10 supports 5 nodes.

Group 11: Group 11

Group 11 Enhed 11 (End Point 11)

Indgang 1

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 12

Sender Basic Report On / Off når indgang 1 aktiveres.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for indgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 3 / 13

Sender Basic Set On / Off når indgang 1 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler, eller til visualisering i den centrale kontroller enhed (f.eks. Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 4 / 14

Sender Binary Switch Set On / Off når indgang 1 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler.

Maks. antal enheder i gruppen: 5

Gruppe 5 / 15

Sender Multilevel Switch Set / Multilevel Switch Start Level Change / Multilevel Switch Stop Level Change når indgang 1 bliver aktiveret.

Kan typisk benyttes til at styre lysdæmpere, gardin styringer, m.m.

Maks. antal enheder i gruppen: 5

Association group 11 supports 5 nodes.

Group 12: Group 12

Group 12 Enhed 12 (End Point 12)

Indgang 2

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 16

Sender Basic Report On / Off når indgang 2 aktiveres.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for indgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 3 / 17

Sender Basic Set On / Off når indgang 2 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler, eller til visualisering i den centrale kontroller enhed (f.eks. Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 4 / 18

Sender Binary Switch Set On / Off når indgang 2 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler.

Maks. antal enheder i gruppen: 5

Gruppe 5 / 19

Sender Multilevel Switch Set / Multilevel Switch Start Level Change / Multilevel Switch Stop Level Change når indgang 2 bliver aktiveret.

Kan typisk benyttes til at styre lysdæmpere, gardin styringer, m.m.

Maks. antal enheder i gruppen: 5

Association group 12 supports 5 nodes.

Group 13: Group 13

Group 13 Enhed 13 (End Point 13)

Indgang 3

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 20

Sender Basic Report On / Off når indgang 3 aktiveres.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for indgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 3 / 21

Sender Basic Set On / Off når indgang 3 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler, eller til visualisering i den centrale kontroller enhed (f.eks. Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 4 / 22

Sender Binary Switch Set On / Off når indgang 3 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler.

Maks. antal enheder i gruppen: 5

Gruppe 5 / 23

Sender Multilevel Switch Set / Multilevel Switch Start Level Change / Multilevel Switch Stop Level Change når indgang 3 bliver aktiveret.

Kan typisk benyttes til at styre lysdæmpere, gardin styringer, m.m.

Maks. antal enheder i gruppen: 5

Association group 13 supports 5 nodes.

Group 14: Group 14

Group 14 Enhed 14 (End Point 14)

Indgang 4

Gruppe 1 / -

Lifeline.

Maks. antal enheder i gruppen: 0

Gruppe 2 / 24

Sender Basic Report On / Off når indgang 4 aktiveres.

Denne gruppe benyttes typisk til at sende status information til den centrale kontroller enhed, for visualisering af status for indgangen (f.eks. til VERA eller Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 3 / 25

Sender Basic Set On / Off når indgang 4 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler, eller til visualisering i den centrale kontroller enhed (f.eks. Fibaro Home Center).

Maks. antal enheder i gruppen: 5

Gruppe 4 / 26

Sender Binary Switch Set On / Off når indgang 4 bliver aktiveret.

Kan f.eks. bruges til at styre relæmoduler.

Maks. antal enheder i gruppen: 5

Gruppe 5 / 27

Sender Multilevel Switch Set / Multilevel Switch Start Level Change / Multilevel Switch Stop Level Change når indgang 4 bliver aktiveret.

Kan typisk benyttes til at styre lysdæmpere, gardin styringer, m.m.

Maks. antal enheder i gruppen: 5

Association group 14 supports 5 nodes.

Technical Information

Endpoints

Endpoint 0

Command Class	Comment
COMMAND_CLASS_NO_OPERATION_V1
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_SWITCH_MULTILEVEL_V1
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_MULTI_CHANNEL_V2
COMMAND_CLASS_CONFIGURATION_V1
COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1
COMMAND_CLASS_POWERLEVEL_V1
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_VERSION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 1

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 2

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 3

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 4

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 5

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 6

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 7

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 8

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 9

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 10

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 11

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 12

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 13

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Endpoint 14

Command Class	Comment
COMMAND_CLASS_BASIC_V1
COMMAND_CLASS_SWITCH_BINARY_V1	Linked to BASIC
COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1
COMMAND_CLASS_ZWAVEPLUS_INFO_V1
COMMAND_CLASS_ASSOCIATION_V2
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Documentation Links

User Manual (Danish)

Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.

Files

lhc5020_0_0.md

Latest commit

History

lhc5020_0_0.md

File metadata and controls

LHC5020 DIN-rail module with 10 digital ouputs and 4 digital inputs

Overview

Inclusion Information

Exclusion Information

Channels

Switch

Dimmer

Switch 1

Switch 2

Switch 3

Switch 4

Switch 5

Switch 6

Switch 7

Switch 8

Switch 9

Switch 10

Switch 11

Switch 12

Switch 13

Switch 14

Device Configuration

Parameter 1: Diode control

Parameter 2: Turn on/off voltage on input terminal 1

Parameter 3: Turn on/off voltage on input terminal 2

Parameter 4: Turn on/off voltage on input terminal 3

Parameter 5: Turn on/off voltage on input terminal 4

Parameter 6: Prel. filter time on input terminals

Parameter 7: Threshold for triggering input

Parameter 8: Threshold time for triggering input

Parameter 9: Function for input terminal 1

Parameter 10: Function for input terminal 2

Parameter 11: Function for input terminal 3

Parameter 12: Function for input terminal 4

Parameter 13: Central Scene notification

Association Groups

Group 1: Lifeline

Group 2: Group 2

Group 3: Group 3

Group 4: Group 4

Group 5: Group 5

Group 6: Group 6

Group 7: Group 7

Group 8: Group 8

Group 9: Group 9

Group 10: Group 10

Group 11: Group 11

Group 12: Group 12

Group 13: Group 13

Group 14: Group 14

Technical Information

Endpoints

Endpoint 0

Endpoint 1

Endpoint 2

Endpoint 3

Endpoint 4

Endpoint 5

Endpoint 6

Endpoint 7

Endpoint 8

Endpoint 9

Endpoint 10

Endpoint 11

Endpoint 12

Endpoint 13

Endpoint 14

Documentation Links