| layout | title |
|---|---|
documentation |
BTZEUMV1 - ZWave |
{% include base.html %}
This describes the Z-Wave device BTZEUMV1, manufactured by Poly-control with the thing type UID of polycontrol_btzeumv1_00_000.
The device is in the category of Lock, defining Devices whose primary pupose is locking something.
The BTZEUMV1 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
The universal module enables the control of existing electrical locking systems via smartphone. It is a circuit board with a relay to switch potential-free contacts. The module is connected near the lock system and actuates engine locks, garage doors, digital cylinders or the door number.
To add or include the Danalock into a Z-Wave network
- Set the controller in inclusion mode
- Push the switch once until you hear two beeps.
To remove or exclude the Danalock from a Z-Wave network
- Set the controller in inclusion mode
- Push the switch once until you hear two beeps.
The following table summarises the channels available for the BTZEUMV1 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Door Lock | lock_door | lock_door | Door | Switch |
| Alarm (access) | alarm_access | alarm_access | Door | Switch |
| Battery Level | battery-level | system.battery_level | Battery | Number |
| Clock Time Offset | time_offset | time_offset | Time | Number |
Lock and unlock the door.
The lock_door channel is of type lock_door and supports the Switch item and is in the Door category.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Locked |
| OFF | Unlocked |
Indicates if the access control alarm is triggered.
The alarm_access channel is of type alarm_access and supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The system.battery-level channel is of type system.battery-level and supports the Number item and is in the Battery category.
This channel provides the battery level as a percentage and also reflects the low battery warning state. If the battery state is in low battery warning state, this will read 0%.
Provides the current time difference for the devices time.
The time_offset channel is of type time_offset and supports the Number item and is in the Time category.
The device has no configuration parameters defined.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The BTZEUMV1 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Z-Wave Plus Lifeline
Association group 1 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_APPLICATION_STATUS_V1 | |
| COMMAND_CLASS_SCHEDULE_ENTRY_LOCK_V1 | |
| COMMAND_CLASS_SCHEDULE_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_DOOR_LOCK_V1 | |
| COMMAND_CLASS_USER_CODE_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V3 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_TIME_V1 | |
| COMMAND_CLASS_TIME_PARAMETERS_V1 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.