| layout | title |
|---|---|
documentation |
10001020-13X - ZWave |
{% include base.html %}
This describes the Z-Wave device 10001020-13X, manufactured by SimonTech S.L.U with the thing type UID of simontech_1000102013x_00_000.
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The 10001020-13X supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The electronic dimmer switch 230V ~ with 2/3 wire phase cut is a switch from Simon 100 serie. These types of dimmer switches have a power of 50W to 240W for traditional loads and 9W to 100W for LED loads. This is highly recommended for all types of uses (domestic, hotels, hospitals ...). The dimmer switch is only compatible with Simon 100 frames.
- Put controller into inclusion mode.
- When the pushbutton is released after a press of (2sec<T<20sec) the device will send a NIF to include the device to the Z-Wave network. Main LED will blink with 0,3 sec period.
- Put controller into exclusion mode.
- When the pushbutton is released after a press of (2sec<T<20sec) the device will send a NIF to include the device to the Z-Wave network. Main LED will blink with 0,3 sec period.
The following table summarises the channels available for the 10001020-13X -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following table provides a summary of the 18 configuration parameters available in the 10001020-13X. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Association LED | Association LED |
| 4 | Set time | Set time |
| 5 | Fade time | Fade time |
| 6 | Minimum dimming value | Minimum dimming value |
| 7 | Maximum dimming value | Maximum dimming value |
| 8 | Last on value | Last on value |
| 9 | Calibration | Calibration |
| 10 | Delay ON | Delay ON |
| 11 | Activation time | Activation time |
| 12 | Behavior of LED in repose | Behavior of LED in repose |
| 13 | Lock input | Lock input |
| 15 | Reset default | Reset default |
| 16 | Delay OFF | Delay OFF |
| 19 | Press action | Press action |
| 20 | Identify | Identify |
| 21 | State of charge | State of charge |
| 23 | Calibration required | Calibration required |
| 27 | Lock long press | Lock long press |
Association LED
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Turns the main LED ON |
| 255 | Turns the main LED OFF |
The manufacturer defined default value is 0 (Turns the main LED ON).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Set time
<td>
Instantly (default value) Disable timming
</td>
<td>
1 second (0x01) to 127 seconds (0x7F) in 1 second resolution
</td>
<td>
1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution
</td>
| 0x00 |
| 0x01-0x7F |
| 0x80-0xFE |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_4_1 and is of type INTEGER.
Fade time
<td>
Instantly (default value) Disable timming
</td>
<td>
1 second (0x01) to 127 seconds (0x7F) in 1 second resolution
</td>
<td>
1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution
</td>
| 0x00 |
| 0x01-0x7F |
| 0x80-0xFE |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Minimum dimming value Stablishes the Max and Min percentages that can be reached. Once the devices gets a value through Z-Wave it Scales the value read according this Min and Max margins. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Maximum dimming value Stablishes the Max and Min percentages that can be reached. Once the devices gets a value through Z-Wave it Scales the value read according this Min and Max margins. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
Last on value Returns or sets the last non zero dimming value. In case of Set the device turns ON the load. Values in the range 1 to 99 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Calibration
The following option values may be configured -:
| Value | Description |
|---|---|
| 1 | Smart Calibrate |
| 2 | Device is calibrated using Trailing Edge |
| 3 | Device is calibrated using Leading Edge |
The manufacturer defined default value is 1 (Smart Calibrate).
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Delay ON
<td>
Instantly (default value) Disable timming
</td>
<td>
1 second (0x01) to 127 seconds (0x7F) in 1 second resolution
</td>
<td>
1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution
</td>
| 0x00 |
| 0x01-0x7F |
| 0x80-0xFE |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_10_1 and is of type INTEGER.
Activation time
<td>
Instantly (default value) Disable timming
</td>
<td>
1 second (0x01) to 127 seconds (0x7F) in 1 second resolution
</td>
<td>
1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution
</td>
| 0x00 |
| 0x01-0x7F |
| 0x80-0xFE |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_11_1 and is of type INTEGER.
Behavior of LED in repose
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED OFF |
| 255 | Central LED on at 20% of maximum level |
The manufacturer defined default value is 0 (LED OFF).
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Lock input
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Unlock the direct control of load |
| 255 | Lock the direct control of load |
The manufacturer defined default value is 0 (Unlock the direct control of load).
This parameter has the configuration ID config_13_1 and is of type INTEGER.
Reset default
The following option values may be configured -:
| Value | Description |
|---|---|
| 17170 | Soft reset |
| 39015 | Hard reset |
The manufacturer defined default value is 17170 (Soft reset).
This parameter has the configuration ID config_15_2_wo and is of type INTEGER.
This is a write only parameter.
Delay OFF
<td>
Instantly (default value) Disable timming
</td>
<td>
1 second (0x01) to 127 seconds (0x7F) in 1 second resolution
</td>
<td>
1 second (0x80) to 127 minutes (0xFE) in 1 minute resolution
</td>
| 0x00 |
| 0x01-0x7F |
| 0x80-0xFE |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_16_1 and is of type INTEGER.
Press action
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Device toggles the load |
| 1 | Device turns ON the load |
| 2 | Device turns OFF the load |
| 4 | Device turns the load ON and then OFF |
| 5 | Device toggles the load and dims |
The manufacturer defined default value is 5 (Device toggles the load and dims).
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Identify The central LED blinks for 5 seconds in order to identify the device. The following option values may be configured -:
| Value | Description |
|---|---|
| 255 | The dimmer blinks |
The manufacturer defined default value is 255 (The dimmer blinks).
This parameter has the configuration ID config_20_1_wo and is of type INTEGER.
This is a write only parameter.
State of charge
<td>
<p>
0x00 Load is OFF
</p>
<p>
0x01 Load is ON
</p>
</td>
<td>
0x00 - 0x063 Last active dimming value
</td>
| First byte |
| Second byte |
The manufacturer defined default value is 0.
This parameter has the configuration ID config_21_2 and is of type INTEGER.
This is a read only parameter.
Calibration required
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Calibration not required |
| 255 | Calibration required |
The manufacturer defined default value is 0 (Calibration not required).
This parameter has the configuration ID config_23_1 and is of type INTEGER.
This is a read only parameter.
Lock long press
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Default long press |
| 255 | Options |
The manufacturer defined default value is 0 (Default long press).
This parameter has the configuration ID config_27_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 10001020-13X supports 2 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. On/Off Report when load state is changed:
- On -> CC Basic, Basic Report, Value 0x01 - 0x63 Report the dimming level
- Off -> CC Basic, Basic Report, Value 0x00
Instant Power Consumption vary over 10% and is stable almost 2sec:
- CC Meter, Meter Report, “Electric meter”, “Consumed”, “Watts”, Size 4, Precision 1, Value (W)
Calibration requirement change. (If device needs to be calibrated and is Added into a Z-Wave network, it will report after receive an Association Set of life line).
- Calibration required -> CC Configuration, Configuration Report, Param 23, Value 0xFF
- Calibration not required -> CC Configuration, Configuration Report, Param 23, Value 0x00
After reset the Z-Wave module, a DEVICE-RESET-LOCALLY-NOTIFICATION is sent.
Association group 1 supports 3 nodes.
On/Off Report when load state is changed:
- On -> CC Basic, Basic Report, Value 0x01 - 0x63 Report the dimming level
- Off -> CC Basic, Basic Report, Value 0x00
Association group 2 supports 20 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V3 | Linked to BASIC |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.