| layout | title |
|---|---|
documentation |
VEGGPLUG - ZWave |
{% include base.html %}
This describes the Z-Wave device VEGGPLUG, manufactured by Sunricher with the thing type UID of sunricher_veggplug_00_000.
The device is in the category of Power Outlet, defining Small devices to be plugged into a power socket in a wall which stick there.
The VEGGPLUG supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Zwave Smart Plug
Press and hold down action button for 10 seconds
Triple click the action button
The following table summarises the channels available for the VEGGPLUG -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Switch | switch_binary | switch_binary | Switch | Switch |
| Scene Number | scene_number | scene_number | Number | |
| Electric meter (volts) | meter_voltage | meter_voltage | Energy | Number |
| Electric meter (kWh) | meter_kwh | meter_kwh | Energy | Number |
| Electric meter (watts) | meter_watts | meter_watts | Energy | Number |
| Electric meter (amps) | meter_current | meter_current | Energy | Number |
| Alarm (power) | alarm_power | alarm_power | Energy | Switch |
Switch the power on and off.
The switch_binary channel is of type switch_binary and supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
Indicates the instantaneous voltage.
The meter_voltage channel is of type meter_voltage and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the energy consumption (kWh).
The meter_kwh channel is of type meter_kwh and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous power consumption.
The meter_watts channel is of type meter_watts and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates the instantaneous current consumption.
The meter_current channel is of type meter_current and supports the Number item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
Indicates if a power alarm is triggered.
The alarm_power channel is of type alarm_power and supports the Switch item and is in the Energy category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 9 configuration parameters available in the VEGGPLUG. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 12 | Percentage Threshold Level | Percentage Threshold Level |
| 13 | Absolute Value Threshold Level | Absolute Value Threshold Level |
| 14 | Time Interval Report Voltage | Time Interval Report Voltage |
| 15 | Time Interval Report Current | Time Interval Report Current |
| 16 | Time Interval Report Power | Time Interval Report Power |
| 17 | Time Interval Report Energy | Time Interval Report Energy |
| 18 | Saving load state before power failure | Saving load state before power failure |
| 19 | Enable/Disable Switch Binary Report | Enable/Disable Switch Binary Report |
| 20 | Enable/Disable Current Protection Function | Enable/Disable Current Protection Function |
Percentage Threshold Level
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_12_1 and is of type INTEGER.
Absolute Value Threshold Level
Values in the range 0 to 65535 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_13_2 and is of type INTEGER.
Time Interval Report Voltage
Values in the range 0 to 2678400 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_14_4 and is of type INTEGER.
Time Interval Report Current
Values in the range 0 to 2678400 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_15_4 and is of type INTEGER.
Time Interval Report Power
Values in the range 0 to 2678400 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_16_4 and is of type INTEGER.
Time Interval Report Energy
Values in the range 0 to 2678400 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_17_4 and is of type INTEGER.
Saving load state before power failure
Values in the range 0 to 2 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_18_1 and is of type INTEGER.
Enable/Disable Switch Binary Report
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_19_1 and is of type INTEGER.
Enable/Disable Current Protection Function
Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_20_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The VEGGPLUG supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_METER_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V3 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.