| layout | title |
|---|---|
documentation |
ZV9101 - ZWave |
{% include base.html %}
This describes the Z-Wave device ZV9101, manufactured by Sunricher with the thing type UID of sunricher_zv9101_00_000.
The device is in the category of Light Bulb, defining Devices that illuminate something, such as bulbs, etc..
The ZV9101 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
The LED dimmer is a Z-Wave device that is used to switch ON/OFF, adjust light intensity and RGB color of the connected RGBW LED light and can be controlled by other Z-Wave devices. The dimmer can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. the device cannot act as Z-Wave network controller (primary or secondary), so a security enabled controller is needed for take full advantage of all functionally for the device. It also supports the Over The Air (OTA) feature for the product’s firmware upgrade. The encryption modes that the LED dimmer supports are S0, S2 Unauthenticated. When the LED dimmer is being included into a Z-Wave network, you can use your primary controller/gateway to enable one encryption mode or disable encryption. (The primary controller/gateway shall support encryption mode configuration).
- Set primary controller/gateway into inclusion mode (Please refer to your primary controllers manual on how to turn your controller into inclusion).
- Power on the LED dimmer, make sure the LED dimmer does not belong to any Z-Wave network (please refer to the part “How to check whether the LED dimmer included to a network” of the manual).
- When the connected LED light flashes quickly for 6 seconds, it means the LED dimmer does not belong to any network. Triple press the “Inclusion/Exclusion” button, it will be set into inclusion mode automatically, and waiting to be included.
- When the connected LED light is under solid on status, it means the LED dimmer has already been included into a network. First you have to set the LED dimmer into exclusion mode, once excluded, it will be set into inclusion mode automatically, and waiting to be included.
The connected LED light stays solid on 3s to indicate successful inclusion.
There are two exclusion methods:
Method 1: Exclusion from the primary controller/gateway as follows:
- Set the primary controller/gateway into exclusion mode (Please refer to your primary controllers manual on how to set your controller into exclusion).
- Triple press the “inclusion/exclusion” button, the LED dimmer will be set to exclusion mode, the connected LED light will flash quickly for 6 seconds, and waiting to be excluded, then LED light stays solid on 3s to indicate successful exclusion.
There are 3 methods for the LED dimmer to quit “exclusion mode”. Once the LED dimmer quits “exclusion mode”, the LED light will stop the fast flash status.
- Automatically quits after successful exclusion.
- Quits after 10 seconds timeout.
- Power off and power on the LED dimmer.
(Note: When the LED dimmer already included to a network, triple press “inclusion/exclusion” button, the LED dimmer will be set into exclusion mode and quit exclusion mode alternatively.)
Method 2: Factory reset the LED dimmer will force the LED dimmer to be excluded from a network. (please refer to the part “Factory Reset” of the manual)
Note: Factory reset is not recommended for exclusion, please use this procedure only if the primary controller/gateway is missing or otherwise inoperable.
1.Short press external button on the LED dimmer to switch ON/OFF the connected LED light.
2.Press and hold down external button on the LED dimmer to adjust light intensity of the connected LED light.
The following table summarises the channels available for the ZV9101 -:
| Channel Name | Channel ID | Channel Type | Category | Item Type |
|---|---|---|---|---|
| Dimmer | switch_dimmer | switch_dimmer | DimmableLight | Dimmer |
| Scene Number | scene_number | scene_number | Number | |
| Color Control | color_color | color_color | ColorLight | Color |
| Color Temperature | color_temperature | color_temperature | ColorLight | Dimmer |
| Alarm (system) | alarm_system | alarm_system | Switch |
The brightness channel allows to control the brightness of a light. It is also possible to switch the light on and off.
The switch_dimmer channel is of type switch_dimmer and supports the Dimmer item and is in the DimmableLight category.
Triggers when a scene button is pressed.
The scene_number channel is of type scene_number and supports the Number item.
The color channel allows to control the color of a light. It is also possible to dim values and switch the light on and off.
The color_color channel is of type color_color and supports the Color item and is in the ColorLight category.
The color temperature channel allows to set the color temperature of a light from 0 (cold) to 100 (warm).
The color_temperature channel is of type color_temperature and supports the Dimmer item and is in the ColorLight category.
Indicates if a system alarm is triggered.
The alarm_system channel is of type alarm_system and supports the Switch item. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
The following table provides a summary of the 8 configuration parameters available in the ZV9101. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 2 | Save Load State | Saving load state before power failure |
| 2 | Saving load state | Saving load state before power failure |
| 3 | Enable/disable basic report | Enables/disables to send Basic report to the Lifeline when load state changed |
| 5 | Cool light stage mode | Choose a cool light stage mode |
| 6 | Stage mode speed | Speed of stage mode |
| 7 | Stage Mode Execution | Execution times of stage mode |
| 8 | Stage Mode Hue | The hue of stage mode |
| 9 | Enable/disable external switch | Enable/disable external switch to be added to and removed from a network |
Saving load state before power failure Parameter number 2 defines the load state after re-power on it:
Value 0 is off state.
Value 1 is on state.
Value 2 is the state before re-power on. Values in the range 0 to 2 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Saving load state before power failure Info: Saving load state before power failure 0 – shutoff load 1 – turn on load 2 – save load state before power failure Values in the range 0 to 2 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Enables/disables to send Basic report to the Lifeline when load state changed Parameter number 3 enables/disables to send Basic report to the Lifeline when load state changed:
Value 0 disables to send.
Value 1 enables to send. Values in the range 0 to 1 may be set.
The manufacturer defined default value is 1.
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Choose a cool light stage mode Parameter number 5 defines light stage mode:
Value 0 inactivates light stage mode.
Value 1 is fade in and fade out mode with colors set by configuration parameter 8.
Value 2 is flash mode with colors set by configuration parameter 8.
Value 3 is rainbow mode with system fixed changing effect.
Value 4 is fade in and fade out mode with randomly changing colors.
Value 5 is flash mode with randomly changing colors.
Value 6 is rainbow mode with randomly changing colors.
Value 7 is random mode, colors switch randomly. Values in the range 0 to 7 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_5_1 and is of type INTEGER.
Speed of stage mode Parameter number 6 defines the speed of stage mode:
Value 0-0xFF configurable, 0 is the slowest, 255 is the fastest. Values in the range 0 to 255 may be set.
The manufacturer defined default value is 243.
This parameter has the configuration ID config_6_1 and is of type INTEGER.
Execution times of stage mode Parameter number 7 defines execution times of stage mode:
Value 0 is unlimited times.
Value 10xFF is 1255 times.
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_7_1 and is of type INTEGER.
The hue of stage mode Parameter number 8 defines the hue of stage mode:
Value 00xFF is hue 0255.
Values in the range 0 to 255 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_8_1 and is of type INTEGER.
Enable/disable external switch to be added to and removed from a network Parameter number 9 enables/disables external switch to be added to and removed from a network:
Value 0 disables.
Value 1 enables. Values in the range 0 to 1 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_9_1 and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The ZV9101 supports 1 association group.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
-
LED Dimmer Factory Reset, send Command Class "Device Reset Locally Notification V1" to associated devices of this group to report factory reset information when factory reset the LED dimmer.
-
When LED dimmer ON/OFF or light intensity value changes, send Command Class "Basic Report" to associated devices of this group to report ON/OFF or light intensity value information.
Association group 1 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_MULTILEVEL_V4 | Linked to BASIC |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_SWITCH_COLOR_V3 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V2 | |
| COMMAND_CLASS_CONFIGURATION_V2 | |
| COMMAND_CLASS_ALARM_V8 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 | |
| COMMAND_CLASS_SECURITY_V1 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.