Test with Prusa Mini

[probonopd]

The Prusa Mini has a slot for an ESP-01 module.

Can we get WirelessPrinting to run on it?

The header on the Buddy board:

Connected to the CPU like this:

Source: https://github.com/prusa3d/Buddy-board-MINI-PCB/blob/master/rev.1.0.0/BUDDY_v1.0.0.pdf CC BY-SA 4.0

Prusa Mini owners are asked to try and report, since I do not have the printer.

[cpeuschel]

Hi @probonopd,

my Prusa Mini is arrived a few days ago. So i will try and report tomorrow.

[cpeuschel]

Hi,

Prusa Mini Firmware: 4.1.0
D1 mini Firmware: acaed49

The d1 can not connect to the printer. here is the telnet output:

Connected to esp_d40674.
Escape character is '^]'.
Connecting at 115200
M115
�M115#discovering#
e3#discovering#
Connecting at 250000
M115
Connecting at 250000
M115
Connecting at 57600
M115
Connecting at 57600
M115
Connecting at 115200
M115
Connecting at 115200
M115
�M115#discovering#
e3#discovering#

i have no clue why it says "discovering".

[probonopd]

Thanks for testing @cpeuschel. Would have been too easy if it "just worked"... #discovering# just means that it is still trying to discover the printer which fails since there is no response coming back from the printer...

Do you have the hardware to check whether you can talk to the printer on ESP-RX and ESP-TX? What happens if you send M115?

[probonopd]

Any Prusa mini owners still around? Please do check whether you can talk to the printer on ESP-RX and ESP-TX using a serial-to-USB converter.

Hi @cpeuschel try switching TX and RX if you have not tried that yet. The printer's TX needs to be connected to the ESP RX and vice versa.

[cpeuschel]

if you would connect Octoprint you must connect the pi via micro USB cable into the printer.

So if we connect the wemos d1 with an micro USB cable directly on the printer maybe it work? Provided there is a way to send the commands (M115, etc.) via USB? @probonopd is that possible?

[probonopd]

Not with just the ESP8266 or ESP32. For this we would need a device with USB host capabilities.

[BluPix]

Hi, I have flashed ESP-01 to your firmware, it worked on the programmer but It didn't work in the Prusa buddy (clone). I have seen in router logs that esp acquired IP, but it didn't communicate from browser. It looks like the actual Prusa firmware set reset pin to turn off ESP.

[probonopd]

Interesting. Thanks for testing. Can you connect to the ESP via telnet and see if there are any messages there?

[vilhelmen]

Hi there, I flashed ESP8266WirelessPrintAsync_d1_mini_acaed49.bin to my ESP8266 and installed it into my mini running 4.2.1-final. I can somewhat confirm what BluPix says, the website does not appear to be loading now that I've installed it, but I have confirmed it acquired a DHCP lease on boot. There don't appear to be any open ports, so it may be going back offline.

I only have a multimeter so I can't do too much diagnostics, but post-boot it appears that IO0, IO2, and EN are high and RST is low.

[vilhelmen]

I built a serial mitm device out of two usb dongles and after grounding RST momentarily it seems to just work, even after switching it off and unplugging it, weirdly enough. Not sure if I broke it or what. Maybe it had it seated poorly? In order to install it I have to take out the power switch and it's a pain in the butt, so I don't want to do that until I know it's working.

I wasn't able to send a large gcode file through (30MB), though I was (seemingly) able to upload a small (830K) sample file with curl that came with the printer. I wasn't able to print or download the uploaded file. I uploaded a text file with a few characters in it and still didn't seem to be able to download it. I think this thing only has 1M of flash, so that could be part of the issue, I'm not sure. I am able to download a 0 byte "Unknown" file on boot, however.

If I fiddle with socat more I may be able to get hex dumps of the communication if you have things you want to try.

[probonopd]

Great @vilhelmen, thanks for testing.

When it is "half-working", can you connect to the ESP with telnet, to see any debug messages?

It is expected that this currently works only for gcode files that are small enough to fit into the internal memory of the ESP chip. For larger files, you could use a different ESP module with a SD card slot and a microSD card attached to the ESP.

I guess this is not what Prusa has in mind with the Prusa mini connector for the ESP01. I guess they will make a firmware that will allow the ESP01 to upload files to the microSD card attached to the printer. But that needs to be implemented in the Prusa firmware. Until they do that, have fun tinkering with WirelessPrinting!

[vilhelmen]

I completely forgot about the telnet port. Now that I'm working on it today, the serial line is completely silent. Telnet connects on boot, but remains quiet and a reconnect fails. RST to GND is reporting -40mV, which seems suspicious.

Connecting/disconnecting RST causes a bunch of data to be output on both lines, but that could be noise, and seems to eventually trigger a reset. The mini starts emitting the 4d 31 31 35 0a 65 33 0a heartbeat/discovery/whatever I saw the day before. The ESP's page is up, but telnet appears to suggest it's stuck in baud rate discovery. The telnet logs say it's receiving the mini's message, but nothing is coming out of the esp today.

The mini, as far as I can tell, doesn't have a microSD slot. There's a mystery barrel plug(?), some sort of small usb, I never remember which is which, a USB A port, and ethernet. There's a nonzero chance I broke something, and my setup is a mess of wires, so something could have come loose. I'll rewire and see what I can come up with, but no promises.

[probonopd]

The mini, as far as I can tell, doesn't have a microSD slot.

Ah, right. I wonder where Prusa wants to buffer large files then? USB? How does it work for wired Ethernet?