Depends on prompt_toolkit and click
Install dependencies
$ pip install click prompt_toolkit --upgrade
Or Install pymodbus with repl support
$ pip install pymodbus[repl] --upgrade
RTU and TCP are supported as of now
✗ pymodbus.console --help
Usage: pymodbus.console [OPTIONS] COMMAND [ARGS]...
Options:
--version Show the version and exit.
--verbose Verbose logs
--broadcast-support Support broadcast messages
--help Show this message and exit.
Commands:
serial
tcp
TCP Options
✗ pymodbus.console tcp --help
Usage: pymodbus.console tcp [OPTIONS]
Options:
--host TEXT Modbus TCP IP
--port INTEGER Modbus TCP port
--framer TEXT Override the default packet framer tcp|rtu
--help Show this message and exit.
SERIAL Options
✗ pymodbus.console serial --help
Usage: pymodbus.console serial [OPTIONS]
Options:
--method TEXT Modbus Serial Mode (rtu/ascii)
--port TEXT Modbus RTU port
--baudrate INTEGER Modbus RTU serial baudrate to use.
--bytesize [5|6|7|8] Modbus RTU serial Number of data bits. Possible
values: FIVEBITS, SIXBITS, SEVENBITS, EIGHTBITS.
--parity [N|E|O|M|S] Modbus RTU serial parity. Enable parity checking.
Possible values: PARITY_NONE, PARITY_EVEN, PARITY_ODD
PARITY_MARK, PARITY_SPACE. Default to 'N'
--stopbits [1|1.5|2] Modbus RTU serial stop bits. Number of stop bits.
Possible values: STOPBITS_ONE,
STOPBITS_ONE_POINT_FIVE, STOPBITS_TWO. Default to '1'
--xonxoff INTEGER Modbus RTU serial xonxoff. Enable software flow
control.
--rtscts INTEGER Modbus RTU serial rtscts. Enable hardware (RTS/CTS)
flow control.
--dsrdtr INTEGER Modbus RTU serial dsrdtr. Enable hardware (DSR/DTR)
flow control.
--timeout FLOAT Modbus RTU serial read timeout in sec.
--write-timeout FLOAT Modbus RTU serial write timeout in sec.
--help Show this message and exit.
To view all available commands type help
TCP
$ pymodbus.console tcp --host 192.168.128.126 --port 5020
> help
Available commands:
client.change_ascii_input_delimiter Diagnostic sub command, Change message delimiter for future requests.
client.clear_counters Diagnostic sub command, Clear all counters and diag registers.
client.clear_overrun_count Diagnostic sub command, Clear over run counter.
client.close Closes the underlying socket connection
client.connect Connect to the modbus tcp server
client.debug_enabled Returns a boolean indicating if debug is enabled.
client.force_listen_only_mode Diagnostic sub command, Forces the addressed remote device to its Listen Only Mode.
client.get_clear_modbus_plus Diagnostic sub command, Get or clear stats of remote modbus plus device.
client.get_com_event_counter Read status word and an event count from the remote device's communication event counter.
client.get_com_event_log Read status word, event count, message count, and a field of event bytes from the remote device.
client.host Read Only!
client.idle_time Bus Idle Time to initiate next transaction
client.is_socket_open Check whether the underlying socket/serial is open or not.
client.last_frame_end Read Only!
client.mask_write_register Mask content of holding register at `address` with `and_mask` and `or_mask`.
client.port Read Only!
client.read_coils Reads `count` coils from a given slave starting at `address`.
client.read_device_information Read the identification and additional information of remote slave.
client.read_discrete_inputs Reads `count` number of discrete inputs starting at offset `address`.
client.read_exception_status Read the contents of eight Exception Status outputs in a remote device.
client.read_holding_registers Read `count` number of holding registers starting at `address`.
client.read_input_registers Read `count` number of input registers starting at `address`.
client.readwrite_registers Read `read_count` number of holding registers starting at `read_address` and write `write_registers` starting at `write_address`.
client.report_slave_id Report information about remote slave ID.
client.restart_comm_option Diagnostic sub command, initialize and restart remote devices serial interface and clear all of its communications event counters .
client.return_bus_com_error_count Diagnostic sub command, Return count of CRC errors received by remote slave.
client.return_bus_exception_error_count Diagnostic sub command, Return count of Modbus exceptions returned by remote slave.
client.return_bus_message_count Diagnostic sub command, Return count of message detected on bus by remote slave.
client.return_diagnostic_register Diagnostic sub command, Read 16-bit diagnostic register.
client.return_iop_overrun_count Diagnostic sub command, Return count of iop overrun errors by remote slave.
client.return_query_data Diagnostic sub command , Loop back data sent in response.
client.return_slave_bus_char_overrun_count Diagnostic sub command, Return count of messages not handled by remote slave due to character overrun condition.
client.return_slave_busy_count Diagnostic sub command, Return count of server busy exceptions sent by remote slave.
client.return_slave_message_count Diagnostic sub command, Return count of messages addressed to remote slave.
client.return_slave_no_ack_count Diagnostic sub command, Return count of NO ACK exceptions sent by remote slave.
client.return_slave_no_response_count Diagnostic sub command, Return count of No responses by remote slave.
client.silent_interval Read Only!
client.state Read Only!
client.timeout Read Only!
client.write_coil Write `value` to coil at `address`.
client.write_coils Write `value` to coil at `address`.
client.write_register Write `value` to register at `address`.
client.write_registers Write list of `values` to registers starting at `address`.
SERIAL
$ pymodbus.console serial --port /dev/ttyUSB0 --baudrate 19200 --timeout 2
> help
Available commands:
client.baudrate Read Only!
client.bytesize Read Only!
client.change_ascii_input_delimiter Diagnostic sub command, Change message delimiter for future requests.
client.clear_counters Diagnostic sub command, Clear all counters and diag registers.
client.clear_overrun_count Diagnostic sub command, Clear over run counter.
client.close Closes the underlying socket connection
client.connect Connect to the modbus serial server
client.debug_enabled Returns a boolean indicating if debug is enabled.
client.force_listen_only_mode Diagnostic sub command, Forces the addressed remote device to its Listen Only Mode.
client.get_baudrate Serial Port baudrate.
client.get_bytesize Number of data bits.
client.get_clear_modbus_plus Diagnostic sub command, Get or clear stats of remote modbus plus device.
client.get_com_event_counter Read status word and an event count from the remote device's communication event counter.
client.get_com_event_log Read status word, event count, message count, and a field of event bytes from the remote device.
client.get_parity Enable Parity Checking.
client.get_port Serial Port.
client.get_serial_settings Gets Current Serial port settings.
client.get_stopbits Number of stop bits.
client.get_timeout Serial Port Read timeout.
client.idle_time Bus Idle Time to initiate next transaction
client.inter_char_timeout Read Only!
client.is_socket_open c l i e n t . i s s o c k e t o p e n
client.mask_write_register Mask content of holding register at `address` with `and_mask` and `or_mask`.
client.method Read Only!
client.parity Read Only!
client.port Read Only!
client.read_coils Reads `count` coils from a given slave starting at `address`.
client.read_device_information Read the identification and additional information of remote slave.
client.read_discrete_inputs Reads `count` number of discrete inputs starting at offset `address`.
client.read_exception_status Read the contents of eight Exception Status outputs in a remote device.
client.read_holding_registers Read `count` number of holding registers starting at `address`.
client.read_input_registers Read `count` number of input registers starting at `address`.
client.readwrite_registers Read `read_count` number of holding registers starting at `read_address` and write `write_registers` starting at `write_address`.
client.report_slave_id Report information about remote slave ID.
client.restart_comm_option Diagnostic sub command, initialize and restart remote devices serial interface and clear all of its communications event counters .
client.return_bus_com_error_count Diagnostic sub command, Return count of CRC errors received by remote slave.
client.return_bus_exception_error_count Diagnostic sub command, Return count of Modbus exceptions returned by remote slave.
client.return_bus_message_count Diagnostic sub command, Return count of message detected on bus by remote slave.
client.return_diagnostic_register Diagnostic sub command, Read 16-bit diagnostic register.
client.return_iop_overrun_count Diagnostic sub command, Return count of iop overrun errors by remote slave.
client.return_query_data Diagnostic sub command , Loop back data sent in response.
client.return_slave_bus_char_overrun_count Diagnostic sub command, Return count of messages not handled by remote slave due to character overrun condition.
client.return_slave_busy_count Diagnostic sub command, Return count of server busy exceptions sent by remote slave.
client.return_slave_message_count Diagnostic sub command, Return count of messages addressed to remote slave.
client.return_slave_no_ack_count Diagnostic sub command, Return count of NO ACK exceptions sent by remote slave.
client.return_slave_no_response_count Diagnostic sub command, Return count of No responses by remote slave.
client.set_baudrate Baudrate setter.
client.set_bytesize Byte size setter.
client.set_parity Parity Setter.
client.set_port Serial Port setter.
client.set_stopbits Stop bit setter.
client.set_timeout Read timeout setter.
client.silent_interval Read Only!
client.state Read Only!
client.stopbits Read Only!
client.timeout Read Only!
client.write_coil Write `value` to coil at `address`.
client.write_coils Write `value` to coil at `address`.
client.write_register Write `value` to register at `address`.
client.write_registers Write list of `values` to registers starting at `address`.
result.decode Decode the register response to known formatters.
result.raw Return raw result dict.
Every command has auto suggestion on the arguments supported , supply arg and value are to be supplied in arg=val format.
> client.read_holding_registers count=4 address=9 slave=1
{
"registers": [
60497,
47134,
34091,
15424
]
}
The last result could be accessed with result.raw command
> result.raw
{
"registers": [
15626,
55203,
28733,
18368
]
}
For Holding and Input register reads, the decoded value could be viewed with result.decode
> result.decode word_order=little byte_order=little formatters=float64
28.17
>
Client settings could be retrieved and altered as well.
> # For serial settings
> # Check the serial mode
> client.method
"rtu"
> client.get_serial_settings
{
"t1.5": 0.00171875,
"baudrate": 9600,
"read timeout": 0.5,
"port": "/dev/ptyp0",
"t3.5": 0.00401,
"bytesize": 8,
"parity": "N",
"stopbits": 1.0
}
> client.set_timeout value=1
null
> client.get_timeout
1.0
> client.get_serial_settings
{
"t1.5": 0.00171875,
"baudrate": 9600,
"read timeout": 1.0,
"port": "/dev/ptyp0",
"t3.5": 0.00401,
"bytesize": 8,
"parity": "N",
"stopbits": 1.0
}
To Send broadcast requests, use --broadcast-support and send requests with slave id as 0.
write_coil, write_coils, write_register, write_registers are supported.
✗ pymodbus.console --broadcast-support tcp --host 192.168.1.8 --port 5020
----------------------------------------------------------------------------
__________ _____ .___ __________ .__
\______ \___.__. / \ ____ __| _/ \______ \ ____ ______ | |
| ___< | |/ \ / \ / _ \ / __ | | _// __ \\____ \| |
| | \___ / Y ( <_> ) /_/ | | | \ ___/| |_> > |__
|____| / ____\____|__ /\____/\____ | /\ |____|_ /\___ > __/|____/
\/ \/ \/ \/ \/ \/|__|
v1.3.0 - [pymodbus, version 3.0.0]
----------------------------------------------------------------------------
> client.write_registers address=0 values=10,20,30,40 slave=0
{
"broadcasted": true
}
> client.write_registers address=0 values=10,20,30,40 slave=1
{
"address": 0,
"count": 4
}
