Ini file visual enhancements

Author: xtitoris

firmware/ini/wideband_dual.ini

@@ -445,9 +445,15 @@ dialog = heater_settings, "Heater Settings"
 ; AFR CAN SETTINGS
 ;
 
+dialog = padding
+   field = "     ", {}, {1}, {1}
+
 dialog = invalid_can_id
    displayOnlyField = "!Invalid CAN ID"
 
+dialog = same_can_id
+   displayOnlyField = "!Same CAN ID on both channels!"
+
 dialog = haltech_afr0_can_settings, "", yAxis
    settingSelector = "Device Id"
       settingOption = "A",  ExtraCanAfrIdx0=0
@@ -515,17 +521,28 @@ dialog = afr1_can_settings, "AFR 1 (right) channel CAN Settings", yAxis
    field = ""
    panel = extra_can_afr1_settings
 
-dialog = can_afr_settings, "CAN AFR Settings", xAxis
+dialog = can_afr_settings_wrapped, "CAN AFR Settings", xAxis
    panel = afr0_can_settings
    panel = afr1_can_settings
 
+dialog = can_afr_settings "", border
+   panel = can_afr_settings_wrapped, North
+
+
 ;
 ; EGT CAN SETTINGS
 ;
 
+dialog = extra_can_egt_channel0_enable, ""
+   field = "CAN output for channel 0 (left)", ExtraCanEgtTx0En
+
+dialog = extra_can_egt_channel1_enable, ""
+   field = "CAN output for channel 1 (right)", ExtraCanEgtTx1En
+
 dialog = extra_can_egt_channel_enable, "", xAxis
-   field = "EGT 0 (left) channel", ExtraCanEgtTx0En
-   field = "EGT 1 (right) channel", ExtraCanEgtTx1En
+   panel = extra_can_egt_channel0_enable
+   panel = padding
+   panel = extra_can_egt_channel1_enable
 
 dialog = extra_can_egt_device_id, "", yAxis
    field = "Dev index", ExtraCanEgtIdx0
@@ -546,19 +563,25 @@ dialog = aemnet0305_egt1_can_settings, "", yAxis
    field = "Dev index", ExtraCanEgtIdx1
    displayOnlyField = "Device ID: 0xA0305 + IDX [0-5]",        Egt1CanId, { 1 }, { ExtraCanEgtTx1 == 1 }, displayInHex ; AEMnet 0305 format
 
-dialog = aemnet0305_egt_can_settings, "", border
-   panel = aemnet0305_egt0_can_settings, East
-   panel = aemnet0305_egt1_can_settings, West
+dialog = aemnet0305_egt_can_settings, "", xAxis
+   panel = aemnet0305_egt0_can_settings, { ExtraCanEgtTx0En == 1 }
+   panel = padding
+   panel = aemnet0305_egt1_can_settings, { ExtraCanEgtTx1En == 1 }
 
-dialog = extra_can_egt_settings, "", yAxis
-   field = "Extra Can Output:"
+dialog = extra_can_egt_protocol, "", yAxis
    field = "Protocol", ExtraCanEgtTx0
+
+dialog = extra_can_egt_settings, "Extra Can Output:", yAxis
+   panel = extra_can_egt_protocol
+   panel = padding
    panel = extra_can_egt_channel_enable, { 1 }, { ExtraCanEgtTx0 > 0 }
    panel = extra_can_egt_device_id,      { 1 }, { ExtraCanEgtTx0 > 0 && ExtraCanEgtTx0 != 1 }
+
    panel = aemnet0305_egt_can_settings,  { 1 }, { ExtraCanEgtTx0 > 0 && ExtraCanEgtTx0 == 1 } ; AEMnet 0305 needs separate offsets for channel 0 and 1
+   panel = same_can_id, {1}, { (ExtraCanEgtTx0 == 1) && (ExtraCanEgtTx1 == 1) && (ExtraCanEgtTx0En == 1) && (ExtraCanEgtTx1En == 1) && (ExtraCanEgtIdx0 == ExtraCanEgtIdx1) }
 
-dialog = can_egt_settings, "CAN EGT Settings"
-   panel = extra_can_egt_settings
+dialog = can_egt_settings, "CAN EGT Settings", border
+   panel = extra_can_egt_settings, North
 
 dialog = auxOut0, "AUX analog out 0 Settings"
    field = "Signal", Aux0InputSel