Skip to content

About

Birthday present for a five-year-old: a Pico WH box whose NeoPixel ring points at the ISS, with clock, weather and nonsense modes. C++ on the Pico SDK, custom wiring and CAD.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Latest commit

 

History

27 Commits

Folders and files

Repository files navigation

Die ISS-Box

A birthday present for a five-year-old: one box, four modes, driven by a big arcade button and a knob.

Mode NeoPixel ring (24 px) NeoPixel 7-segment LCD
UHR 24-hour dial HH:MM, NTP-synced date + weekday
ISS compass pointing at the space station distance in km ground position
WETTER thermometer arc, blue → red temperature temp + humidity
PUPS countdown, then a 0–24 bar graph score 0–99 verdict

The ring is the centrepiece: 24 pixels divide 360° into exactly 15° each, so with a north arrow marked on the case, the lit pixel genuinely points at the ISS. Colour carries elevation — deep blue when it's on the far side of the planet, blazing white when it's overhead.

Whatever mode the box is in, it interrupts itself when the ISS actually rises above the horizon: buzzer, ring flash, and an automatic switch to ISS mode.

Hardware

Raspberry Pi Pico WH (RP2040), C++17 on the Pico SDK. The "H" means headers are pre-soldered, including the three debug pins — so a spare plain Pico can act as an SWD probe when needed.

Function GPIO Pin
NeoPixel ring data GP2 4
I2C SDA / SCL (SHT3x + LCD) GP4 / GP5 6 / 7
NeoPixel digits data GP7 10
Buzzer GP9 12
Rotary encoder SW / CLK / DT GP13 / GP14 / GP15 17 / 19 / 20
Arcade button / lamp GP16 / GP17 21 / 22
MiCS-5524 A0 / EN GP26 / GP27 31 / 32

The arcade lamp is a low-current LED with its own series resistor, driven straight from GP17 on PWM at 12 mA drive strength — no transistor needed.

The gas sensor runs at 5 V and its A0 reaches the 3.3 V ADC through a divider: 10 k from A0, 15.64 k (10 k + 4.7 k + 470 + 470 in series) to ground. Sized for the Raspberry Pi adapter's 5.1 V rather than a round 5.0 V — 3.111 V at nominal, 3.270 V at the +5% worst case, 94% of the ADC range. A 100 nF cap from GP26 to AGND settles the sampling.

The 470 Ω resistors on each NeoPixel data line belong close to the pixels, not close to the Pico: their job is limiting current into the first pixel's input protection diodes, so they have to sit at the input they protect.

Pins are spread deliberately: the final build is hand-soldered onto an Adafruit Mint Tin-Sized PermaProto, so unrelated signals get a free pin between them. Pins from the same module stay adjacent, since they arrive as one bundle.

Peripherals: SCD40 CO2+temp+humidity (0x62) and/or SHT3x temp+humidity (0x44), DFRobot Gravity LCD1602 RGB (DFR0464), 24-pixel NeoPixel ring, 32-pixel NeoPixel seven-segment (4 digits x 8 pixels, own data line), MiCS-5524 gas sensor, rotary encoder, arcade button, buzzer.

Powered entirely through the Pico's own USB connector — a USB-C Raspberry Pi supply with a USB-C-to-micro-USB cable. VBUS (pin 40) then distributes 5 V to the pixels and the gas sensor. One source means no back-feeding, so no Schottky diode and no separate USB breakout are needed.

Pixel brightness is clamped in software against a current budget — 56 pixels at full white would pull ~3.4 A.

Building

./go.sh                # build
./go.sh flash          # build and load onto the board
./go.sh flash monitor  # ...and open the serial console

First flash needs BOOTSEL held while plugging in USB. After that the firmware exposes a reset interface and picotool reboots the board itself.

Configuration

cp src/config.h.example src/config.h

src/config.h holds WiFi credentials and the home coordinates the ISS compass points relative to. It is gitignored and must stay that way.

About

Birthday present for a five-year-old: a Pico WH box whose NeoPixel ring points at the ISS, with clock, weather and nonsense modes. C++ on the Pico SDK, custom wiring and CAD.

Topics

Resources

Stars

0 stars

Watchers

0 watching

Forks

Releases

Packages

Contributors

Languages