This plugin is to control devices that have been flashed with Tasmota via web calls.
Requires minimum Tasmota firmware version 5.11.0.
Single relay devices need to use 1 for index.
WARNING: Tasmota firmware version 15.5.0+ requires SetOption128 ON to allow HTTP API communication. Issue 221
Install via the bundled Plugin Manager or manually using this URL:
https://github.com/jneilliii/OctoPrint-Tasmota/archive/master.zip
Once installed go into settings and enter the ip address for your Tasmota device. Adjust additional settings as needed.
-
- Enable thermal runaway monitoring.
- When enabled if temperatures exceed configured maximums enabled relay will be powered off.
- Max Bed Temp
- Maximum temperature bed can reach before automatic power off is triggered.
- Max Extruder Temp
- Maximum temperature extruders can reach before automatic power off is triggered.
- Error Event Monitoring
- When enabled if printer reports an error relays with the option enabled will be automatically powered off.
- Disconnect Event Monitoring
- When enabled if printer becomes disconnected relays with the option enabled will be automatically powered off.
- Upload Event Monitoring
- When enabled auto power on enabled devices when file is uploaded to OctoPrint with the option to automatically start printing.
- Include uploads via web interface
- Enable to auto power on when uploading via the web interface rather than from a Slicer with the option to automatically start.
- Automtically start print after on
- Enable to automatically start the print after the Tasmota device is powered on and printer auto connects.
- Connect Event Monitoring
- When enabled auto power on enabled devices when the Connect button is pressed in OctoPrint.
- Enable polling of status.
- When enabled the status of relays will be checked based on the Polling Interval supplied.
- Polling Interval
- How many minutes between status checks of all relays when polling is enabled.
- Cost per kWh
- Amount used to multiply total kWh by to estimate power cost. Leave 0 if you do not have a power reporting device.
- Request Timeout
- How many seconds to wait for responses from tasmota device before it is considered offline.
- Enable debug logging.
- Report additional information in plugin_tasmota_debug.log for troubleshooting.
- Power Off on Idle
- Automatically power off all relays with the option Off on Idle enabled after configured idle timeout, target tempoerature is reached, and timelapse is completed.
- Abort Power Off Timeout
- Pop up will be displayed for this amount of time in seconds to allow for delaying power off of relays.
- Idle Timeout
- Amount of time that will lapse before printer is considered idle and relays will be powered off.
- Idle Target Temperature
- Power off will be delayed until all heaters reach this temperature.
- GCode Commands to Ignore for Idle
- Comma separated list of gcode commands to ignore for determining printer idle state.
- Wait for Timelapse
- When enabled idle power off will wait for timelapse to complete before powering off. Uncheck this to not wait, helpful for very long prints and timelapse rendering.
- Enable thermal runaway monitoring.
-
- IP
- The ip or hostname of tasmota device.
- Index
- Index of the relay, specifically used for multiple plug relay devices. Leave blank for single relay devices.
- Label
- Name to display on hover of the navbar button.
- Username
- Username to connect to web interface. Currently, not configurable in Tasmota, use the default username admin.
- Password
- Password configured for Web Admin Portal of Tasmota device.
- Verify
- Use this button to make sure that the plugin can communicate with your Tasmota device.
- On Color
- Color to display when device is on.
- Off Color
- Color to display when device is off.
- Unknown Color
- Color to display when device status is unknown.
- Icon Class
- Icon class name from the fontawesome library.
- LED
- Is an LED or WS2812 type device connected, enter brightness value as percentage.
- Sensor Identifier
- Sensor identifier for connected sensors, ie DHT11 or BME280
- On with Upload
- Automatically power on when file is uploaded with the option to start printing automatically.
- On with Connect
- Automatically power on when pressing Connect button.
- Off on Idle
- Automatically power off when printer is idle.
- Thermal Runaway
- Power off if temperature exceeds configured max temperatures.
- Off on Error
- Automatically power off this relay when Error Event Monitoring is enabled.
- Off on Disconnect
- Automatically power off this relay when Disconnect Event Monitoring is enabled.
- Auto Connect
- Automatically connect to your printer after configured delay from power on.
- Auto Disconnect
- Automatically disconnect from printer and then power off relay after configured delay.
- Warning Prompt
- Prompt for confirmation before powering off via the navbar button.
- Warn While Printing
- Prompt for confirmation before powering off when a print is active.
- Use Countdown Timers
- Use Tasmota's built-in countdown functionality to offload the power operations. Helpful for safe shutdown of pi.
- On Delay Countdown
- Amount of delay in seconds for powering on device.
- Off Delay Countdown
- Amount of delay in seconds for powering off device.
- GCODE On / Off Trigger
- When checked this will enable the processing of M80 and M81 commands from gcode to power on/off plug. Syntax for gcode command is M80/M81 followed by hostname/ip and index. For example if your plug is 192.168.1.2 and index of 1 your gcode command would be M80 192.168.1.2 1
- GCODE On Delay
- Amount of delay in seconds before powering on device.
- GCODE Off Delay
- Amount of delay in seconds for powering off device.
- Run System Command After On
- When checked will run the system command configured in setting below after sending on command to device.
- System Command to Run
- System command to run after the on command is sent to device.
- Delay
- Delay in seconds before system command is run.
- Run System Command Before Off
- When checked will run the system command configured in setting below before sending off command to device.
- System Command to Run
- System command to run before the on command is sent to device.
- Delay
- Delay in seconds after system command is run before powering off device.
- IP
- Pi Safe Shutdown
With these options the raspberry pi will be shutdown 5 seconds after the idle timeout is reached (as configured on the main settings page) and send a backlog command to your Tasmota device to power off after a 60 second delay.
1.1.6 (07/31/2021)
- add more granular permissions for separating device control and viewing status/UI elements.
If you experience issues with this plugin or need assistance please use the issue tracker by clicking issues above.
Check out my other plugins here
- Andreas Lindermayr
- @TheTuxKeeper
- @tideline3d
- SimplyPrint
- Andrew Beeman
- Calanish
- Lachlan Bell
- Jonny Bergdahl
I, jneilliii, programmed this plugin for fun and do my best effort to support those that have issues with it, please return the favor and leave me a tip or become a Patron if you find this plugin helpful and want me to continue future development.
No paypal.me? Send funds via PayPal to jneilliii@gmail.com